SP2-XXX (Drum)

2005

[Charge DC Voltage] Charge Roller DC Voltage Adjustment

(Paper Type, Process Speed, Color)

Paper Type –> Plain, Thick 1, Thick 2

Plain: High speed, Thick 1: Middle speed, Thick 2&FINE: Low speed

Adjusts the DC component of the charge roller bias in the various print modes.

Charge bias (DC component) is automatically adjusted during process control; therefore, adjusting these settings does not effect while process control mode (SP3-041-1 Default: ON) is activated. When deactivating process control mode with SP3-041-1, the values in these SP modes are used for printing.

001

Plain: Bk

*ENG

[0 to 1000 / 690 / 10 –V/step]

002

Plain: M

*ENG

003

Plain: C

*ENG

004

Plain: Y

*ENG

005

Thick 1: Bk

*ENG

006

Thick 1: M

*ENG

007

Thick 1: C

*ENG

008

Thick 1: Y

*ENG

009

Thick 2&FINE: Bk

*ENG

010

Thick 2&FINE: M

*ENG

011

Thick 2&FINE: C

*ENG

012

Thick 2&FINE: Y

*ENG

[Charge DC: Correction]

013

PCU:Plain

*ENG

[–100 to 100 / -29 / 1 –V/step]

014

PCU:Thick 1

*ENG

[–100 to 100 / -28 / 1 –V/step]

015

PCU:Thick 2&FINE

*ENG

[–100 to 100 / -28 / 1 –V/step]

016

HVP:Plain

*ENG

[–100 to 100 / 20 / 1 –V/step]

017

HVP:Thick 1

*ENG

[–100 to 100 / 20 / 1 –V/step]

018

HVP: Thick 2&FINE

*ENG

[–100 to 100 / 29 / 1 –V/step]

2006

[Charge AC Voltage] Charge Roller AC Voltage Adjustment

(Paper Type, Process Speed, Color)

Paper Type –> Plain, Thick 1, Thick 2

Plain: High speed, Thick 1: Middle speed, Thick 2&FINE: Low speed

Adjusts the AC component of the charge roller bias in the various print modes.

Charge bias (AC component) is adjusted by environment correction (SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1 is set to "1: manual control".

001

Plain: Bk

*ENG

[0 to 3 / 1.9 / 0.01 KV/step]

002

Plain: M

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

003

Plain: C

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

004

Plain: Y

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

005

Thick 1: Bk

*ENG

[0 to 3 / 1.9 / 0.01 KV/step]

006

Thick 1: M

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

007

Thick 1: C

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

008

Thick 1: Y

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

009

Thick 2&FINE: Bk

*ENG

[0 to 3 / 1.9 / 0.01 KV/step]

010

Thick 2&FINE: M

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

011

Thick 2&FINE: C

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

012

Thick 2&FINE: Y

*ENG

[0 to 3 / 2.2 / 0.01 KV/step]

2007

[Charge AC Current: LL] Charge Roller AC Current Adjustment for LL

(Color)

Displays/sets the AC current target of the charge roller for LL environment (Low temperature and Low humidity). DFU

001

Environmental Target: Bk

*ENG

[0 to 3 / 0.68 / 0.01 mA/step]

002

Environmental Target: M

*ENG

[0 to 3 / 0.83/ 0.01 mA/step]

003

Environmental Target: C

*ENG

004

Environmental Target: Y

*ENG

2008

[Charge AC Current: ML] Charge Roller AC Current Adjustment for MM

(Color)

Displays/sets the AC current target of the charge roller for ML environment (Meddle temperature and Low humidity). DFU

001

Environmental Target: Bk

*ENG

[0 to 3 / 0.7 / 0.01 mA/step]

002

Environmental Target: M

*ENG

[0 to 3 / 0.87 / 0.01 mA/step]

003

Environmental Target: C

*ENG

004

Environmental Target: Y

*ENG

2009

[Charge AC Current: MM] Charge Roller AC Current Adjustment for MM

(Color)

Displays/sets the AC current target of the charge roller for MM environment (Middle temperature and Middle humidity). DFU

001

Environmental Target: Bk

*ENG

[0 to 3 / 0.73 / 0.01 mA/step]

002

Environmental Target: M

*ENG

[0 to 3 / 0.89 / 0.01 mA/step]

003

Environmental Target: C

*ENG

004

Environmental Target: Y

*ENG

2010

[Charge AC Current: MH] Charge Roller AC Current Adjustment for MH

(Color)

Displays/sets the AC current target of the charge roller for MH environment (Middle temperature and High humidity). DFU

001

Environmental Target: Bk

*ENG

[0 to 3 / 0.74 / 0.01 mA/step]

002

Environmental Target: M

*ENG

[0 to 3 / 0.89 / 0.01 mA/step]

003

Environmental Target: C

*ENG

004

Environmental Target: Y

*ENG

2011

[Charge AC Current: HH] Charge Roller AC Current Adjustment for HH

(Color)

Displays/sets the AC current target of the charge roller for HH environment (High temperature and High humidity). DFU

001

Environmental Target: Bk

*ENG

[0 to 3 / 0.74 / 0.01 mA/step]

002

Environmental Target: M

*ENG

[0 to 3 / 0.87 / 0.01 mA/step]

003

Environmental Target: C

*ENG

004

Environmental Target: Y

*ENG

2012

[Charge Output Control]

001

AC Voltage

*ENG

Selects the AC voltage control type.

[0 or 1 / 0 / 1 /step]

0: Process control

1: Manual control (AC voltages are decided with SP2006.)

2013

[Environmental Correction: PCU]

001

Current Environmental: Display

*ENG

Displays the environmental condition, which is measured in absolute humidity.

[1 to 5 / – / 1 /step]

1: LL (LL <= 4.3 g/m³)

2: ML (4.3 < ML <= 11.3 g/m³)

3: MM (11.3 < MM <= 18.0 g/m³)

4: MH (18.0 < MH <= 24.0 g/m³)

5: HH (24.0 g/m³ < HH)

002

Forced Setting

*ENG

Selects the environmental condition manually.

[0 to 5 / 0 / 1 /step]

0: The environmental condition is determined automatically.

1: LL, 2: ML, 3: MM, 4: MH, 5: HH

003

Absolute Humidity: Threshold 1

*ENG

Changes the humidity threshold between LL and ML.

[0 to 100 / 3.0 / 0.01 g/m³/step]

004

Absolute Humidity: Threshold 2

*ENG

Changes the humidity threshold between ML and MM.

[0 to 100 / 8.0 / 0.01 g/m³/step]

005

Absolute Humidity: Threshold 3

*ENG

Changes the humidity threshold between MM and MH.

[0 to 100 / 15.0 / 0.01 g/m³/step]

006

Absolute Humidity: Threshold 4

*ENG

Changes the humidity threshold between MH and HH.

[0 to 100 / 15.0 / 0.01 g/m³/step]

007

Current Temp.: Display

*ENG

Displays the current temperature.

[0 to 100 / 0 / 1 deg/step]

008

Current Relative Humidity: Display

*ENG

Displays the current relative humidity.

[0 to 100 / 0 / 1%RH/step]

009

Current Absolute Humidity: Display

*ENG

Displays the absolute humidity.

[0 to 100 / 0 / 0.01 g/m³/step]

010

Previous Environmental: Display

*ENG

Displays the previous environmental condition, which is measured in absolute humidity.

[1 to 5 / – / 1 /step]

1: LL, 2: ML, 3: MM, 4: MH, 5: HH

011

Previous Temp.: Display

*ENG

Displays the previous temperature.

[0 to 100 / 0 / 1 deg/step]

012

Previous Relative Humidity: Display

*ENG

Displays the previous relative humidity.

[0 to 100 / 0 / 1%RH/step]

013

Previous Absolute Humidity: Display

*ENG

Displays the previous absolute humidity.

[0 to 100 / 0 / 0.01 g/m³/step]

2014

[Charge AC Control: Setting] DFU

Specifies the charge AC control interval or thresholod for each condition.

001

Exec Interval: Power ON

*ENG

[0 to 2000 / 500 / 1 page/step]

002

Exec Interval: Print

*ENG

003

Page Interval

*ENG

[0 to 500 / 10 / 5 page/step]

004

Temperature

*ENG

[0 to 99 / 99 / 1 deg/step]

005

Relative Humidity

*ENG

[0 to 99 / 50 / 1 %RH/step]

006

Absolute Humidity

*ENG

[0 to 99 / 12 / 1 g/m³/step]

007

Temp Threshold M

*ENG

[0 to 99 / 5 / 1 deg/step]

008

RH Threshold M

*ENG

[0 to 99 / 25 / 1 %RH/step]

009

AH Threshold M

*ENG

[0 to 99 / 6 / 1 g/m³/step]

010

Temp Threshold S

*ENG

[0 to 20 / 1 / 0.1 deg/step]

011

RH Threshold S

*ENG

[0 to 50 / 5 / 1 %RH/step]

012

AH Threshold S

*ENG

[0 to 20 / 1 / 0.1 g/m³/step]

013

Non-use Time

*ENG

[0 to 1440 / 360 / 10 min/step]

2015

[Charge AC Control:Result]

001

Bk

*ENG

[0 to 9 / 0 / 1 /step]

0: Success

1: Out of tolerance range

2: Out of adjustable range

3: Adjustment incompleted

002

M

*ENG

003

C

*ENG

004

Y

*ENG

2101

[Color Registration Correction] FA

These values are the parameters for the automatic line position adjustment and are adjusted at the factory. However, you must input a value for SP2101-001 after replacing the laser optics housing unit. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section. The value should be provided with the new laser optics housing unit.

001

Main Dot: Bk

*ENG

[–512 to 511 / 0 / 1 dot/step]

002

Main Dot: Ma

*ENG

003

Main Dot: Cy

*ENG

004

Main Dot: Ye

*ENG

005

Sub Line: Bk

*ENG

[–16384 to 16383 / 0 / 1 line/step]

006

Sub Line: Ma

*ENG

007

Sub Line: Cy

*ENG

008

Sub Line: Ye

*ENG

2102

[Magnification Adjustment] DFU

001

Main Mag.: High Speed: Bk

*ENG

These are results of the main scan length adjustment.

[0 to 560 / 280 / 1 /step]

002

Main Mag.: Medium Speed: Bk

*ENG

003

Main Mag.: Low Speed: Bk

*ENG

004

Main Mag.: High Speed: M

*ENG

005

Main Mag.: Medium Speed: M

*ENG

006

Main Mag.: Low Speed: M

*ENG

007

Main Mag.: High Speed: C

*ENG

008

Main Mag.: Medium Speed: C

*ENG

009

Main Mag.: Low Speed: C

*ENG

010

Main Mag.: High Speed: Y

*ENG

011

Main Mag.: Medium Speed: Y

*ENG

012

Main Mag.: Low Speed: Y

*ENG

013

Offset: Mag Bk1-2

*ENG

[-256 to 255 / 0 / 1 sub-dot/step]

014

Offset: Mag M1-2

*ENG

015

Offset: Mag C1-2

*ENG

016

Offset: Mag Y1-2

*ENG

2103

[Erase Margin Adjustment] (Area, Paper Size)

Adjusts the erase margin by deleting image data at the margins.

001

Lead Edge Width

*ENG

[0 to 9.9 / 4.2 / 0.1 mm/step]

002

Trail. Edge Width

*ENG

003

Left

*ENG

[0 to 9.9 / 2 / 0.1 mm/step]

004

Right

*ENG

006

Duplex Trail. L Size

*ENG

[0 to 4 / 0 / 0.1 mm/step]

007

Duplex Trail. M Size

*ENG

[0 to 4 / 0 / 0.1 mm/step]

008

Duplex Trail. S Size

*ENG

[0 to 4 / 0 / 0.1 mm/step]

009

Duplex Left Edge

*ENG

[0 to 1.5 / 0.3 / 0.1 mm/step]

010

Duplex Right Edge

*ENG

011

Duplex Trail. L Size:Thick

*ENG

[0 to 4 / 1 / 0.1 mm/step]

012

Duplex Trail. M Size:Thick

*ENG

[0 to 4 / 0.8 / 0.1 mm/step]

013

Duplex Trail. S Size:Thick

*ENG

[0 to 4 / 0.6 / 0.1 mm/step]

014

Duplex Left Edge:Thick

*ENG

[0 to 1.5 / 0.3 / 0.1 mm/step]

015

Duplex Right Edge:Thick

*ENG

2105

[LD Power Adj.] (Process Speed, Color)

Adjusts the LD power of each color for each process speed.

Each LD power setting is decided by process control.

001

High Speed: Bk

*ENG

[50 to 120 / 100 / 1%/step]

Decreasing a value makes lines thinner on the output.

Increasing a value makes lines thicker on the output.

002

High Speed: Ma

*ENG

003

High Speed: Cy

*ENG

004

High Speed: Ye

*ENG

005

Middle Speed: Bk

*ENG

[50 to 120 / 100 / 1%/step]

Decreasing a value makes lines thinner on the output.

Increasing a value makes lines thicker on the output.

006

Middle Speed: Ma

*ENG

007

Middle Speed: Cy

*ENG

008

Middle Speed: Ye

*ENG

009

Low Speed: Bk

*ENG

[50 to 120 / 100 / 1%/step]

Decreasing a value makes lines thinner on the output.

Increasing a value makes lines thicker on the output.

010

Low Speed: Ma

*ENG

011

Low Speed: Cy

*ENG

012

Low Speed: Ye

*ENG

2106

[Polygon Rotation Time]

Adjusts the time of the polygon motor rotation. DFU

001

Warming-Up

*ENG

[0 to 60 / 10 / 1 sec/step]

002

Job End

*ENG

2107

[Image Parameter]

DFU

001

Image Gamma Flag

*ENG

[0 or 1 / 1 / 1 /step]

002

Shading Correction Flag

*ENG

2109

[Test Pattern]

Generates the test pattern using "COPY Window" tab in the LCD.

003

Pattern Selection

-

[0 to 23 / 0 / 1/step]

0 None

1: Vertical Line (1dot)

2: Vertical Line (2dot)

3: Horizontal (1dot)

4: Horizontal (2dot)

5: Grid Vertical Line

6: Grid Horizontal Line

7: Grid pattern Small

8: Grid pattern Large

9: Argyle Pattern Small

10: Argyle Pattern Large

11. Independent Pattern (1dot)

12. Independent Pattern (2dot)

13. Independent Pattern (4dot)

14. Trimming Area

16: Hound’s Tooth Check (Horizontal)

17: Band (Horizontal)

18: Band (Vertical)

19: Checker Flag Pattern

20: Grayscale Vertical Margin

21: Grayscale Horizontal Margin

23: Full Dot Pattern

005

Color Selection

-

Specifies the color for the test pattern.

[1 to 4 / 1 / 1/step]

1: All colors, 2: Magenta, 3: Yellow, 4: Cyan

006

Density: Bk

-

Specifies the color density for the test pattern.

[0 to 15 / 15 / 1 /step]

0: Lightest density

15: Darkest density

007

Density: Ma

-

008

Density: Cy

-

009

Density: Ye

-

2111

[Forced Line Position Adj.]

001

Mode a

-

Executes the fine line position adjustment twice.

If this SP is not completed (NG is displayed), do SP2111-003 first and then try this SP again.

002

Mode b

-

Executes the fine line position adjustment once.

If this SP is not completed, do SP2111-003 first and then try this SP again.

003

Mode c

-

Executes the rough line position adjustment once.

After doing this SP, make sure to execute SP2111-001 or -002. Otherwise, the line position adjustment is not perfectly done.

2112

[TM/ID Sensor Check] ID Sensor Check FA

001

Execute

This SP is used to check the ID sensors at the factory. The results of this SP are displayed in SP2140 to SP2145.

2117

[Skew Adjustment]

Specifies a skew adjustment value for the skew motor M, C or Y.

These SPs must be used when a new laser optics housing unit is installed or when SC285 occurs. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section.

001

Pulse: M

*ENG

[–100 to 100 / 0 / 1 pulse/step]

002

Pulse: C

*ENG

003

Pulse: Y

*ENG

2118

[Skew Adjustment]

001

Execute: M

*ENG

Changes the current skew adjustment values to the values specified with SP2117.

These SPs must be used when a new laser optics housing unit is installed or when SC285 occurs. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section.

002

Execute: C

*ENG

003

Execute: Y

*ENG

2119

[Skew Adjustment Display]

Displays the current skew adjustment value for each skew motor.

001

M

*ENG

[–50 to 50 / 0 / 1 pulse/step]

002

C

*ENG

003

Y

*ENG

2120

[Thick Paper Skew Adj] Not used

Selects the skew adjustment for thick paper.

001

On/Off

*ENG

[0 or 1 / 1 / 1 /step]

0: Off, 1: On

2140

[ID Sensor Check Result] DFU

Displays the results of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Bk

*ENG

[0 to 1024 / 0 / 1/step]

002

M

*ENG

003

C

*ENG

004

Y

*ENG

005

Front

*ENG

006

Center

*ENG

007

Rear

*ENG

2141

[ID Sensor Check Result: Ave.] DFU

Displays the average result values of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Bk

*ENG

[0 to 5.5 / 0 / 0.01V/step]

002

M

*ENG

003

C

*ENG

004

Y

*ENG

005

Front

*ENG

006

Center

*ENG

007

Rear

*ENG

2142

[ID Sensor Check Result] DFU

Displays the maximum result values of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Maximum: Bk

*ENG

[0 to 5.5 / 0 / 0.01V/step]

002

Maximum: M

*ENG

003

Maximum: C

*ENG

004

Maximum: Y

*ENG

005

Maximum: Front

*ENG

006

Maximum: Center

*ENG

007

Maximum: Rear

*ENG

2143

[ID Sensor Check Result] DFU

Displays the minimum result values of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Minimum: Bk

*ENG

[0 to 5.5 / 0 / 0.01V/step]

002

Minimum: M

*ENG

003

Minimum: C

*ENG

004

Minimum: Y

*ENG

005

Minimum: Front

*ENG

006

Minimum: Center

*ENG

007

Minimum: Rear

*ENG

2144

[ID Sensor Check Result] DFU

Displays the maximum result 2 values of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Maximum 2: Bk

*ENG

[0 to 5.5 / 0 / 0.01V/step]

002

Maximum 2: M

*ENG

003

Maximum 2: C

*ENG

004

Maximum 2: Y

*ENG

005

Maximum 2: Front

*ENG

006

Maximum 2: Center

*ENG

007

Maximum 2: Rear

*ENG

2145

[ID Sensor Check Result] DFU

Displays the minimum result 2 values of the ID sensor check.

Bk, M, C, Y: ID sensors for the process control

Front, Center, Rear: ID sensors for the automatic line position adjustment

001

Minimum 2: Bk

*ENG

[0 to 5.5 / 0 / 0.01V/step]

002

Minimum 2: M

*ENG

003

Minimum 2: C

*ENG

004

Minimum 2: Y

*ENG

005

Minimum 2: Front

*ENG

006

Minimum 2: Center

*ENG

007

Minimum 2: Rear

*ENG

2150

[Area Mag. Correction] LD Pulse Area Correction (Color, Area) FA

Adjusts the magnification for each area. The main scan (297 mm) is divided into 8 areas. Area 1 is at the front side of the machine (left side of the image) and area 8 is at the rear side of the machine (right side of the image).

Decreasing a value makes the image shift to the left side on the print.

Increasing a value makes the image shift to the right side on the print.

1 pulse = 1/16 dot

027

Area 0: Bk

*ENG

[-256 to 255 / 0 / 1sub-dot/step]

028

Area 1: Bk

*ENG

Adjusts the area magnification for LD 0.

[–256 to 255 / 0 / 1 sub-dot/step ]

029

Area 2: Bk

*ENG

030

Area 3: Bk

*ENG

031

Area 4: Bk

*ENG

032

Area 5: Bk

*ENG

033

Area 6: Bk

*ENG

034

Area 7: Bk

*ENG

035

Area 8: Bk

*ENG

036

Area 9: Bk

*ENG

Not used

037

Area 10: Bk

*ENG

038

Area 11: Bk

*ENG

039

Area 12: Bk

*ENG

079

Area 0: Ma

*ENG

Not used

080

Area 1: Ma

*ENG

Adjusts the area magnification for LD 0. [–255to 255 / 0 / 1 sub-dot/step]

081

Area 2: Ma

*ENG

[–256to 255 / 0 / 1 sub-dot/step]

082

Area 3: Ma

*ENG

083

Area 4: Ma

*ENG

084

Area 5: Ma

*ENG

085

Area 6: Ma

*ENG

086

Area 7: Ma

*ENG

087

Area 8: Ma

*ENG

088

Area 9: Ma

*ENG

Not used

089

Area 10: Ma

*ENG

090

Area 11: Ma

*ENG

091

Area 12: Ma

*ENG

131

Area 0: Cy

*ENG

Not used

132

Area 1: Cy

*ENG

Adjusts the area magnification for LD 0.

[–256 to 255 / 0 / 1 sub-dot/step]

133

Area 2: Cy

*ENG

134

Area 3: Cy

*ENG

135

Area 4: Cy

*ENG

136

Area 5: Cy

*ENG

137

Area 6: Cy

*ENG

138

Area 7: Cy

*ENG

139

Area 8: Cy

*ENG

140

Area 9: Cy

*ENG

Not used

141

Area 10: Cy

*ENG

142

Area 11: Cy

*ENG

143

Area 12: Cy

*ENG

183

Area 0: Ye

*ENG

Not used

184

Area 1: Ye

*ENG

Adjusts the area magnification for LD 0.

[–256 to 255 / 0 / 1 sub-dot/step]

185

Area 2: Ye

*ENG

186

Area 3: Ye

*ENG

187

Area 4: Ye

*ENG

188

Area 5: Ye

*ENG

189

Area 6: Ye

*ENG

190

Area 7: Ye

*ENG

191

Area 8: Ye

*ENG

192

Area 9: Ye

*ENG

Not used

193

Area 10: Ye

*ENG

194

Area 11: Ye

*ENG

195

Area 12: Ye

*ENG

2152

[Area Shad. Correct. Setting] FA

Adjusts the area correction value for each LD power.

The main scan is divided into 16 areas. However, the image areas are limited from area 1 to area 14.

For BK and Magenta, area 1 is at the rear side of the machine (left side of the image) and area 14 is at the front side of the machine (right side of the image).

For Cyan and Yellow, area 1 is at the front side of the machine (right side of the image) and area 14 is at the rear side of the machine (left side of the image).

001

Area 0: Bk

*ENG

This is for the synchronizing detection board.

[50 to 150 / 100 / 1 %/step]

002

Area 1: Bk

*ENG

003

Area 2: Bk

*ENG

004

Area 3: Bk

*ENG

005

Area 4: Bk

*ENG

006

Area 5: Bk

*ENG

007

Area 6: Bk

*ENG

008

Area 7: Bk

*ENG

009

Area 8: Bk

*ENG

010

Area 9: Bk

*ENG

011

Area 10: Bk

*ENG

012

Area 11: Bk

*ENG

013

Area 12: Bk

*ENG

014

Area 13: Bk

*ENG

015

Area 14: Bk

*ENG

016

Area 15: Bk

*ENG

This is out of the image area.

[50 to 150 / 100 / 1 %/step]

033

Area 0: M

*ENG

This is for the synchronizing detection board.

034

Area 1: M

*ENG

[50 to 150 / 100 / 1 %/step]

035

Area 2: M

*ENG

036

Area 3: M

*ENG

037

Area 4: M

*ENG

038

Area 5: M

*ENG

039

Area 6: M

*ENG

040

Area 7: M

*ENG

041

Area 8: M

*ENG

042

Area 9: M

*ENG

043

Area 10: M

*ENG

044

Area 11: M

*ENG

045

Area 12: M

*ENG

046

Area 13: M

*ENG

047

Area 14: M

*ENG

048

Area 15: M

*ENG

This is out of the image area.

[50 to 150 / 100 / 1 %/step]

065

Area 0: C

*ENG

This is for the synchronizing detection board.

[50 to 150 / 100 / 1 %/step]

066

Area 1: C

*ENG

[50 to 150 / 100 / 1 %/step]

067

Area 2: C

*ENG

068

Area 3: C

*ENG

069

Area 4: C

*ENG

070

Area 5: C

*ENG

071

Area 6: C

*ENG

072

Area 7: C

*ENG

073

Area 8: C

*ENG

074

Area 9: C

*ENG

075

Area 10: C

*ENG

076

Area 11: C

*ENG

077

Area 12: C

*ENG

078

Area 13: C

*ENG

079

Area 14: C

*ENG

080

Area 15: C

*ENG

This is out of the image area.

[50 to 150 / 100 / 1 %/step]

097

Area 0: Y

*ENG

This is for the synchronizing detection board.

[50 to 150 / 100 / 1 %/step]

098

Area 1: Y

*ENG

[50 to 150 / 100 / 1 %/step]

099

Area 2: Y

*ENG

100

Area 3: Y

*ENG

101

Area 4: Y

*ENG

102

Area 5: Y

*ENG

103

Area 6: Y

*ENG

104

Area 7: Y

*ENG

105

Area 8: Y

*ENG

106

Area 9: Y

*ENG

107

Area 10: Y

*ENG

108

Area 11: Y

*ENG

109

Area 12: Y

*ENG

110

Area 13: Y

*ENG

111

Area 14: Y

*ENG

112

Area 15: Y

*ENG

This is out of the image area.

2160

[Vertical Line Width] DFU

Adjusts the width of the vertical line.

001

600dpi:Bk

*ENG

[10 to 15 / 13 / 1 /step]

002

600dpi:Ma

*ENG

[10 to 15 / 15 / 1 /step]

003

600dpi:Cy

*ENG

004

600dpi:Ye

*ENG

005

1200dpi:Bk

*ENG

006

1200dpi:Ma

*ENG

007

1200dpi:Cy

*ENG

008

1200dpi:Ye

*ENG

2180

[Line Position Adj. Setting Clear]

001

Color Regist.

-

DFU

002

Main Scan Length Detection

-

003

MUSIC Result

-

004

Area Magnification Correction

-

2181

[Line Position Adj. Result]

Displays the values for each correction.

• "Paper Int. Mag: Subdot" indicates the magnification correction value between two sheets of paper.

• "Mag.Cor. Subdot" indicates the magnification correction value.

• "M. Scan Erro." indicates the shift correction value in the main scan direction.

• "S. Scan Erro." Indicates the shift correction value in the sub scan direction.

• "M. Cor.: Dot" indicates the dot correction value in the main scan direction.

• "M. Cor.: Subdot" indicates the sub dot correction value in the main scan direction.

• Bk: Black, M: Magenta, C: Cyan, Y: Yellow

001

Paper Int. Mag: Subdot: Bk

*ENG

[–32768 to 32767 / 0 / 1 pulse/step]

002

Mag.Cor. Subdot: Bk

*ENG

[–32768 to 32767 / 0 / 1 pulse/step]

003

Skew: M

*ENG

[–5000 to 5000 / 0 / 0.001 um/step]

005

M. Scan Erro.: Left: M

*ENG

[–5000 to 5000 / 0 / 0.001 um/step]

006

M. Scan Erro.: Center: M

*ENG

007

M. Scan Erro.: Right: M

*ENG

008

S. Scan Erro.: Left: M

*ENG

009

S. Scan Erro.: Center: M

*ENG

010

S. Scan Erro.: Right: M

*ENG

011

M. Cor.: Dot: M

*ENG

[–512 to 511 / 0 / 1 dot/step]

012

M. Cor.: Subdot: M

*ENG

[–15 to 15 / 0 / 1 pulse/step]

013

Paper Int. Mag: Subdot: M

*ENG

[–32768 to 32767 / 0 / 1 pulse/step]

014

Mag.Cor. Subdot: M

*ENG

015

M. Left Mag.: Subdot: M

*ENG

016

M. Right Mag.: Subdot: M

*ENG

017

S. Cor.: 600 Line: M

*ENG

[–16384 to 16383 / 0 / 1 line/step]

018

S. Cor.: 600 Sub: M

*ENG

[–1 to 1 / 0 / 0.001 line/step]

019

S. Cor.: 1200 Line: M

*ENG

[–16384 to 16383 / 0 / 1 line/step]

020

S. Cor.: 1200 Sub: M

*ENG

[–1 to 1 / 0 / 0.001 line/step]

021

Skew: C

*ENG

[–5000 to 5000 / 0 / 0.001 um/step]

023

M. Scan Erro.: Left: C

*ENG

[–5000 to 5000 / 0 / 0.001 um/step]

024

M. Scan Erro.: Center: C

*ENG

025

M. Scan Erro.: Right: C

*ENG

026

S. Scan Erro.: Left: C

*ENG

027

S. Scan Erro.: Center: C

*ENG

028

S. Scan Erro.: Right: C

*ENG

029

M. Cor.: Dot: C

*ENG

[–512 to 511 / 0 / 1 dot/step]

030

M. Cor.: Subdot: C

*ENG

[–15 to 15 / 0 / 1 pulse/step]

031

Paper Int. Mag: Subdot: C

*ENG

[–32768 to 32767 / 0 / 1 pulse/step]

032

Mag.Cor. Subdot: C

*ENG

033

M. Left Mag.: Subdot: C

*ENG

034

M. Right Mag.: Subdot: C

*ENG

035

S. Cor.: 600 Line: C

*ENG

[–16384 to 16383 / 0 / 1 line/step]

036

S. Cor.: 600 Sub: C

*ENG

[–1 to 1 / 0 / 0.001 line/step]

037

S. Cor.: 1200 Line: C

*ENG

[–16384 to 16383 / 0 / 1 line/step]

038

S. Cor.: 1200 Sub: C

*ENG

[–1 to 1 / 0 / 0.001 line/step]

039

Skew: Y

*ENG

[–5000 to 5000 / 0 / 0.001 um/step]

041

M. Scan Erro.: Left: Y

*ENG

042

M. Scan Erro.: Center: Y

*ENG

043

M. Scan Erro.: Right: Y

*ENG

044

S. Scan Erro.: Left: Y

*ENG

045

S. Scan Erro.: Center: Y

*ENG

046

S. Scan Erro.: Right: Y

*ENG

047

M. Cor.: Dot: Y

*ENG

[–512 to 511 / 0 / 1 dot/step]

048

M. Cor.: Subdot: Y

*ENG

[–15 to 15 / 0 / 1 pulse/step]

049

Paper Int. Mag: Subdot: Y

*ENG

[–32768 to 32767 / 0 / 1 pulse/step]

050

Mag.Cor. Subdot: Y

*ENG

051

M. Left Mag.: Subdot: Y

*ENG

052

M. Right Mag.: Subdot: Y

*ENG

053

S. Cor.: 600 Line: Y

*ENG

[–16384 to 16383 / 0 / 1 line/step]

054

S. Cor.: 600 Sub: Y

*ENG

[–1 to 1 / 0 / 0.001 line/step]

055

S. Cor.: 1200 Line: Y

*ENG

[–16384 to 16383 / 0 / 1 line/step]

056

S. Cor.: 1200 Sub: Y

*ENG

[–1 to 1 / 0 / 0.001 line/step]

2182

[Line Position Adj. Offset]

(Color) M. Scan: Main scan, S. Scan: Sub-scan

High: 154 mm/sec, Medium: 111 mm/sec, Low: 77 mm/sec

001

M Magnification

*ENG

Adjusts the line position manually.

[-1 to 1 / 0 / 0.001%/step]

When line shifts are not corrected by the automatic line position adjustment, do this SP.

Increasing a value reduces the image in the main scan direction.

Decreasing a value enlarges the image in the main scan direction.

002

C Magnification

*ENG

003

Y Magnification

*ENG

004

M. Scan: High: Dot: M

*ENG

[-512 to 511 / 0 / 1 dot/step]

005

M. Scan: High: Subdot: M

*ENG

[-15 to 15 / 0 / 1 pulse/step]

006

M. Scan: Medium: Dot: M

*ENG

[-512 to 511 / 0 / 1 dot/step]

007

M. Scan: Medium: Subdot: M

*ENG

[-15 to 15 / 0 / 1 pulse/step]

008

M. Scan: Low: Dot: M

*ENG

[-512 to 511 / 0 / 1 dot/step]

009

M. Scan: Low: Subdot: M

*ENG

[-15 to 15 / 0 / 1 pulse/step]

010

M. Scan: High: Dot: C

*ENG

[-512 to 511 / 0 / 1 dot/step]

011

M. Scan: High: Subdot: C

*ENG

[-15 to 15 / 0 / 1 pulse/step]

012

M. Scan: Medium: Dot: C

*ENG

[-512 to 511 / 0 / 1 dot/step]

013

M. Scan: Medium: Subdot: C

*ENG

[-15 to 15 / 0 / 1 pulse/step]

014

M. Scan: Low: Dot: C

*ENG

[-512 to 511 / 0 / 1 dot/step]

015

M. Scan: Low: Subdot: C

*ENG

[-15 to 15 / 0 / 1 pulse/step]

016

M. Scan: High: Dot: Y

*ENG

[-512 to 511 / 0 / 1 dot/step]

017

M. Scan: High: Subdot: Y

*ENG

[-15 to 15 / 0 / 1 pulse/step]

018

M. Scan: Medium: Dot: Y

*ENG

[-512 to 511 / 0 / 1 dot/step]

019

M. Scan: Medium: Subdot: Y

*ENG

[-15 to 15 / 0 / 1 pulse/step]

020

M. Scan: Low: Dot: Y

*ENG

[-512 to 511 / 0 / 1 dot/step]

021

M. Scan: Low: Subdot: Y

*ENG

[-15 to 15 / 0 / 1 pulse/step]

022

S. Scan: High: Line: M

*ENG

[-16384 to 16383 / 0 / 1 line/step]

023

S. Scan: High: Subline: M

*ENG

[–1 to 1 / 0 / 0.001 /line]

024

S. Scan: Medium: Line: M

*ENG

[-16384 to 16383 / 0 / 1 line/step]

025

S. Scan: Medium: Subline: M

*ENG

[–1 to 1 / 0 / 0.001 /line]

026

S. Scan: Low: Line: M

*ENG

[-16384 to 16383 / 0 / 1 line/step]

027

S. Scan: Low: Subline: M

*ENG

Not used

028

S. Scan: High: Line: C

*ENG

[-16384 to 16383 / 0 / 1 line/step]

029

S. Scan: High: Subline: C

*ENG

[–1 to 1 / 0 / 0.001 /line]

030

S. Scan: Medium: Line: C

*ENG

[-16384 to 16383 / 0 / 1 line/step]

031

S. Scan: Medium: Subline: C

*ENG

[–1 to 1 / 0 / 0.001 /line]

032

S. Scan: Low: Line: C

*ENG

[-16384 to 16383 / 0 / 1 line/step]

033

S. Scan: Low: Subline: C

*ENG

Not used

034

S. Scan: High: Line: Y

*ENG

[-16384 to 16383 / 0 / 1 line/step]

035

S. Scan: High: Subline: Y

*ENG

[–1 to 1 / 0 / 0.001 /line]

036

S. Scan: Medium: Line: Y

*ENG

[-16384 to 16383 / 0 / 1 line/step]

037

S. Scan: Medium: Subline: Y

*ENG

[–1 to 1 / 0 / 0.001 /line]

038

S. Scan: Low: Line: Y

*ENG

[-16384 to 16383 / 0 / 1 line/step]

039

S. Scan: Low: Subline: Y

*ENG

Not used

2183

[Main Scan Length Detection] DFU

001

Execute: High: Bk

-

Executes the adjustment for the main scan length detection manually.

002

Execute: Medium: Bk

-

003

Execute: Low: Bk

-

004

Execute: High: M

-

005

Execute: Medium: M

-

006

Execute: Low: M

-

007

Execute: High: C

-

008

Execute: Medium: C

-

009

Execute: Low: C

-

010

Execute: High: Y

-

011

Execute: Medium: Y

-

012

Execute: Low: Y

-

2184

[Main Scan Length Detection Target] DFU

001

Execute: Bk

-

Executes the target value for the main scan length detection.

002

Execute: M

-

003

Execute: C

-

004

Execute: Y

-

2185

[Main Scan Length Detection Disp.]

Displays/adjusts the target value for the main scan magnification correction of the line position adjustment.

After replacing the laser optics housing unit, input the standard value for Bk provided with the new unit. For details, see "Laser Optics Housing Unit" in the "Replacement Adjustment" section. It is not necessary to input the values for the other colors; these are automatically adjusted after doing the line position adjustment.

001

Bk

*ENG

[0 to 266667 / 249449 / 1 sub-dot/step]

002

M

*ENG

003

C

*ENG

004

Y

*ENG

2186

[Main Scan Length Detection] DFU

001

Selection

*ENG

[0 or 1 / 1 / 1/step]

0: Mag. Correction OFF,

1: Mag. Correction ON

Enables or disables the main scan length detection for the laser.

002

Paper Interval

*ENG

[0 to 999 / 1 / 1 sec/step]

Adjusts the interval of the main scan length detection for the laser.

2190

[Line Position Adj.] DFU

001

Paper Int. Mag.: Subdot: Bk

*ENG

[0 or 1 / 1 / 1/step]

002

Paper Int. Mag.: Subdot: M

*ENG

003

Paper Int. Mag.: Subdot: C

*ENG

004

Paper Int. Mag.: Subdot: Y

*ENG

005

M. Scan Mag.: Subdot: M

*ENG

[0 or 1 / 1 / 1/step]

0: Disable correction,

1: Enable correction

006

M. Scan Mag.: Subdot: C

*ENG

007

M. Scan Mag.: Subdot: Y

*ENG

008

Area Mag.: Subdot: M

*ENG

[0 or 1 / 1 / 1/step]

009

Area Mag.: Subdot: C

*ENG

010

Area Mag.: Subdot: Y

*ENG

012

Detection Error Level

*ENG

[-3500 to 3500 / 0 / 1 m/step]

2191

[MUSIC Coefficient Setting] Line Position Adjustment: Coefficient Setting DFU

ch 0: ID sensor at rear, ch 1: ID sensor at center, ch 2: ID sensor at front

001

ch 0: Filter: Front: a1

*ENG

[–131071 to 131071 / 125869 / 1 bit/step]

002

ch 0: Filter: Front: a2

*ENG

[–131071 to 131071 / –60488 / 1 bit/step]

003

ch 0: Filter: Front: b0

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

004

ch 0: Filter: Front: b1

*ENG

[–131071 to 131071 / 77 / 1 bit/step]

005

ch 0: Filter: Front: b2

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

006

ch 0: Filter: Rear: a1

*ENG

[–131071 to 131071 / 128596 / 1 bit/step]

007

ch 0: Filter: Rear: a2

*ENG

[–131071 to 131071 / –63398 / 1 bit/step]

008

ch 0: Filter: Rear: b0

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

009

ch 0: Filter: Rear: b1

*ENG

[–131071 to 131071 / 168 / 1 bit/step]

010

ch 0: Filter: Rear: b2

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

011

ch 1: Filter: Front: a1

*ENG

[–131071 to 131071 / 125869 / 1 bit/step]

012

ch 1: Filter: Front: a2

*ENG

[–131071 to 131071 / –60488 / 1 bit/step]

013

ch 1: Filter: Front: b0

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

014

ch 1: Filter: Front: b1

*ENG

[–131071 to 131071 / 77 / 1 bit/step]

015

ch 1: Filter: Front: b2

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

016

ch 1: Filter: Rear: a1

*ENG

[–131071 to 131071 / 128596 / 1 bit/step]

017

ch 1: Filter: Rear: a2

*ENG

[–131071 to 131071 / –63398 / 1 bit/step]

018

ch 1: Filter: Rear: b0

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

019

ch 1: Filter: Rear: b1

*ENG

[–131071 to 131071 / 168 / 1 bit/step]

020

ch 1: Filter: Rear: b2

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

021

ch 2: Filter: Front: a1

*ENG

[–131071 to 131071 / 125869 / 1 bit/step]

022

ch 2: Filter: Front: a2

*ENG

[–131071 to 131071 / –60488 / 1 bit/step]

023

ch 2: Filter: Front: b0

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

024

ch 2: Filter: Front: b1

*ENG

[–131071 to 131071 / 77 / 1 bit/step]

025

ch 2: Filter: Front: b2

*ENG

[–131071 to 131071 / 39 / 1 bit/step]

026

ch 2: Filter: Rear: a1

*ENG

[–131071 to 131071 / 128596 / 1 bit/step]

027

ch 2: Filter: Rear: a2

*ENG

[–131071 to 131071 / –63398 / 1 bit/step]

028

ch 2: Filter: Rear: b0

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

029

ch 2: Filter: Rear: b1

*ENG

[–131071 to 131071 / 168 / 1 bit/step]

030

ch 2: Filter: Rear: b2

*ENG

[–131071 to 131071 / 84 / 1 bit/step]

031

Q Format Selection

*ENG

[0 to 3 / 3 / 1/step]

2192

[MUSIC Threshold Setting] Line Position Adjustment: Threshold Setting DFU

ch 0: ID sensor at rear, ch 1: ID sensor at center, ch 2: ID sensor at front

001

ch 0: 1st

*ENG

[0.5 to 3 / 1.2 / 0.1 V/step]

002

ch 0: 2nd

*ENG

003

ch 0: 3rd

*ENG

004

ch 0: 4th

*ENG

005

ch 1: 1st

*ENG

006

ch 1: 2nd

*ENG

007

ch 1: 3rd

*ENG

008

ch 1: 4th

*ENG

009

ch 2: 1st

*ENG

010

ch 2: 2nd

*ENG

011

ch 2: 3rd

*ENG

012

ch 2: 4th

*ENG

2193

[MUSIC Condition Set] Line Position Adjustment: Condition Setting

001

Auto Execution

*ENG

[0 or 1 / 1 / 1 ]

0: OFF, 1: ON

Enables/disables the automatic line position adjustment

002

Page: Job End: BW+FC

*ENG

[0 to 999 / 500 / 1 page/step]

Adjusts the threshold of the line position adjustment for BW and color printing mode after job end.

003

Page: Job End: FC

*ENG

[0 to 999 / 200 / 1 page/step]

Adjusts the threshold of the line position adjustment for color printing mode after job end.

004

Page: Interrupt: BW+FC

*ENG

[0 to 999 / 200 / 1 page/step]

Adjusts the threshold of the line position adjustment for BW and color printing mode during job.

005

Page: Interrupt: FC

*ENG

[0 to 999 / 200 / 1 page/step]

Adjusts the threshold of the line position adjustment for color printing mode during jobs.

006

Page: Stand-By: BW

*ENG

[0 to 999 / 100 / 1 page/step]

Adjusts the threshold of the line position adjustment for BW printing mode in stand-by mode. The line position adjustment is done when the number of outputs in BW printing mode reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is satisfied.

007

Page: Stand-By: FC

*ENG

[0 to 999 / 100 / 1 page/step]

Adjusts the threshold of the line position adjustment for BW printing mode in stand-by mode. The line position adjustment is done when the number of outputs in color printing mode reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is satisfied.

008

Temp.

*ENG

[0 to 100 / 5 / 1deg/step]

Adjust the temperature change threshold for the line position adjustment (Mode b: adjustment once). The timing for line position adjustment depends on the combinations of several conditions. Section Descriptions" section.

009

Time

*ENG

[1 to 1440 / 300 / 1 minute/step]

Adjust the time threshold for the line position adjustment (Mode b: adjustment once). The timing for line position adjustment depends on the combinations of several conditions.

010

Magnification

*ENG

[0 to 1 / 0.1 / 0.01%/step]

Adjusts the magnification threshold for line position adjustment. If the length of the main scan is changed by this amount since the previous MUSIC, then MSUIC is done again.

011

Temp. 2

*ENG

[0 to 100 / 10 / 1deg/step]

Adjust the temperature change threshold for the line position adjustment (Mode a: adjustment twice). The timing for line position adjustment depends on the combinations of several conditions.

012

Time 2

*ENG

[1 to 9999 / 600 / 1 minute/step]

Adjust the time threshold for the line position adjustment (Mode a: adjustment twice). The timing for line position adjustment depends on the combinations of several conditions.

013

Page: Power ON:BW+FC

*ENG

[0 to 999 / 200 / 1 page/step]

Adjusts the threshold for the condition of the line position adjustment for BW and color printing mode. The condition of the line position adjustment is determined for large condition difference and small condition difference when the number of outputs in color printing mode reaches the value specified with this SP and the condition of SP3-510-009 or SP3-510-010 is satisfied. However, it is basically not necessary to adjust this SP.

2194

[MUSIC Execution Result] Line Position Adjustment: Execution Result

001

Year

*ENG

[0 to 99 / 0 / 1 year/step]

Displays the year of the last MUSIC execution.

002

Month

*ENG

[1 to 12 / 1 / 1 month/step]

Displays the month of the last MUSIC execution.

003

Day

*ENG

[1 to 31 / 1 / 1 day/step]

Displays the date of the last MUSIC execution.

004

Hour

*ENG

[0 to 23 / 0 / 1 hour/step]

Displays the time (hour) of the last MUSIC execution.

005

Minute

*ENG

[0 to 59 / 0 / 1 minute/step]

Displays the time (minute) of the last MUSIC execution.

006

Temperature

*ENG

[0 to 100 / 0 / 1 deg/step]

Displays the temperature of the last MUSIC execution.

007

Execution Result

*ENG

[0 or 1 / 0 / 1 /step]

0: Completed successfully, 1: Failed

008

Number of Execution

*ENG

[0 to 999999 / 0 / 1 times/step]

009

Number of Failure

*ENG

[0 to 999999 / 0 / 1 times/step]

010

Error Result: M

*ENG

[0 to 9 / 0 / 1 /step]

0: Not done

1: Completed successfully

2: Cannot detect patterns

3: Fewer lines on the pattern than the target

4: Not used

5: Out of the adjustment range

6 to 9: Not used

011

Error Result: C

*ENG

012

Error Result: Y

*ENG

2197

[MUSIC Start Time]

DFU

001

MUSIC Start Time (EDT)

*ENG

[10 to 40 / 20 / 10ms/step]

002

TM Sensor Position

*ENG

[50 to 500 / 105.5 / 0.1mm/step]

2198

[Music A/D Interval]

ADC Trigger Counter

001

ADC Trigger Counter

*ENG

[7.5 to 20 / 10 / 0.1 s/step]

2199

[Music Error Time Setting]

DFU

001

Error Detection Counter

*ENG

[0.5 to 4 / 2.5 / 0.1 sec /step]

2220

[Skew Origin Set]

Executes the skew motor initialization in the laser optics unit.

001

M: Skew Motor

-

-

002

C: Skew Motor

-

-

003

Y: Skew Motor

-

-

2221

[LD Power] LD Power Control

Adjusts the fixed LD power for each line speed and color.

These SPs are activated only when SP3-041-002 is set to "0".

Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed

001

Plain: Bk

*ENG

[0 to 200 / 100 / 1%/step]

Increasing this value makes the image density darker.

002

Plain: M

*ENG

003

Plain: C

*ENG

004

Plain: Y

*ENG

005

Thick 1: Bk

*ENG

006

Thick 1: M

*ENG

007

Thick 1: C

*ENG

008

Thick 1: Y

*ENG

009

Thick 2&FINE: Bk

*ENG

010

Thick 2&FINE: M

*ENG

011

Thick 2&FINE: C

*ENG

012

Thick 2&FINE: Y

*ENG

2229

[Development DC Vias] Development DC Bias Adjustment

Adjusts the development bias.

Development bias is automatically adjusted during process control; therefore, adjusting these settings has no effect while Process Control (SP3-041-001 Default: ON) is activated.

After deactivating Process Control with SP3-041-001, the values in these SP modes are used for printing.

Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed

001

Plain: Bk

*ENG

[0 to 800 / 550 / 10 –V/step]

002

Plain: M

*ENG

003

Plain: C

*ENG

004

Plain: Y

*ENG

005

Thick 1: Bk

*ENG

006

Thick 1: M

*ENG

007

Thick 1: C

*ENG

008

Thick 1: Y

*ENG

009

Thick 2&FINE:Bk

*ENG

010

Thick 2&FINE:M

*ENG

011

Thick 2&FINE:C

*ENG

012

Thick 2&FINE:Y

*ENG

2241

[Temperature/Humidity: Display]

Displays the environment temperature and humidity.

001

Temperature

-

[–1280 to 1270 / - / 0.1deg/step]

002

Relative Humidity

-

[0 to 1000 / - / 0.1 %RH/step]

003

Absolute Humidity

-

[0 to 100 / - / 0.01 g/m³/step]

2302

[Environmental Correction: Transfer]

Environmental Correction: Image Transfer Belt Unit

001

Current Environmental Display

-

Displays the current environment condition.

002

Forced Setting

*ENG

Sets the environment condition manually.

[0 to 6 / 0 / 1 /step]

0: Automatic environment control

1: LL (Low temperature/ Low humidity)

2: ML (Middle temperature/ Low humidity)

3: MM (Middle temperature/ Middle humidity)

4: MH (Middle temperature/ High humidity)

5: HH (High temperature/ High humidity)

003

Absolute Humidity: Threshold 1

*ENG

Adjusts the threshold value between LL and ML.

[0 to 100 / 4 / 0.01 g/m³/step]

004

Absolute Humidity: Threshold 2

*ENG

Adjusts the threshold value between ML and MM.

[0 to 100 / 8 / 0.01 g/m³/step]

005

Absolute Humidity: Threshold 3

*ENG

Adjusts the threshold value between MM and MH.

[0 to 100 / 16 / 0.01 g/m³/step]

006

Absolute Humidity: Threshold 4

*ENG

Adjusts the threshold value between MH and HH.

[0 to 100 / 24 / 0.01 g/m³/step]

007

Temp Threshold

*ENG

[–5 to 30 / 5 / 1 deg/step]

2308

[Paper Size Correction]

Adjusts the threshold value for the paper size correction.

001

Threshold 1

*ENG

[0 to 350 / 297 / 1 mm/step]

Threshold 1 < paper:

Paper is detected as "S1" size.

002

Threshold 2

*ENG

[0 to 350 / 257 / 1 mm/step]

Threshold 2 < paper < Threshold 1:

Paper is detected as "S2" size.

003

Threshold 3

*ENG

[0 to 350 / 210 / 1 mm/step]

Threshold 3 < paper < Threshold 2:

Paper is detected as "S3" size.

004

Threshold 4

*ENG

[0 to 350 / 148 / 1 mm/step]

Threshold 4 < paper < Threshold 3:

Paper is detected as "S4" size.

Paper < Threshold 4:

Paper is detected as "S5" size.

2311

[Non Image Area: Bias]

001

Image Transfer

*ENG

Adjusts the bias of the image transfer belt between images. This value is added to the value of the image transfer belt bias.

[10 to 250 / 100 / 5 %/step]

002

Paper Transfer

*ENG

Adjusts the bias of the paper transfer roller between images.

[0 to 2000 / 500 / 1 V/step]

2326

[Transfer Roller CL: Bias] Transfer Roller Cleaning: Bias Adjustment

001

Positive

*ENG

[0 to 2100 / 500 / 100 V /step]

Adjusts the positive voltage of the paper transfer roller for cleaning the paper transfer roller.

002

Negative

*ENG

[10 to 400 / 100 / 10 %/step]

Adjusts the negative current of the paper transfer roller for cleaning the paper transfer roller.

003

Positive

*ENG

[0 to 2100 / 2000 / 100 V/step]

Adjusts the negative current limit of the paper transfer roller for cleaning the paper transfer roller.

004

Negative

*ENG

[10 to 400 / 100 / 10 %/step]

2351

[Common: BW: Bias] Image Transfer Belt: B/W: Bias Adjustment

Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed

001

ITB unit: Plain

*ENG

[0 to 80 / 25 / 1 A]

Adjusts the current for the image transfer belt in B/W mode for plain paper.

002

ITB unit: Thick 1

*ENG

[0 to 80 / 12 / 1 A]

Adjusts the current for the image transfer belt in B/W mode for thick 1 paper.

003

ITB unit: Thick 2 & FINE

*ENG

[0 to 80 / 12 / 1 A]

Adjusts the current for the image transfer belt in B/W mode for thick 2 paper or FINE mode.

2357

[Common: FC: Bias] Image Transfer Belt: Full Color: Bias Adjustment

Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed

001

ITB unit: Plain: Bk

*ENG

[0 to 80 / 22 / 1 A]

Adjusts the current for the image transfer belt for Black in full color mode for plain paper.

002

ITB unit: Plain: M

*ENG

[0 to 80 / 25 / 1 A]

Adjusts the current for the image transfer belt for Magenta in full color mode for plain paper.

003

ITB unit: Plain: C

*ENG

[0 to 80 / 22 / 1 A]

Adjusts the current for the image transfer belt for Cyan in full color mode for plain paper.

004

ITB unit: Plain: Y

*ENG

[0 to 80 / 28 / 1 A]

Adjusts the current for the image transfer belt for Yellow in full color mode for plain paper.

005

ITB unit: Thick 1: Bk

*ENG

[0 to 80 / 11 / 1 A]

Adjusts the current for the image transfer belt for Black in full color mode for thick 1 paper.

006

ITB unit: Thick 1: M

*ENG

[0 to 80 / 12 / 1 A]

Adjusts the current for the image transfer belt for Magenta in full color mode for thick 1 paper.

007

ITB unit: Thick 1: C

*ENG

[0 to 80 / 11 / 1 A]

Adjusts the current for the image transfer belt for Cyan in full color mode for thick 1 paper.

008

ITB unit: Thick 1: Y

*ENG

[0 to 80 / 14 / 1 A]

Adjusts the current for the image transfer belt for Yellow in full color mode for thick 1 paper.

009

ITB unit: Thick 2 & FINE: Bk

*ENG

[0 to 80 / 11 / 1 A]

Adjusts the current for the image transfer belt for Black in full color mode for Thick 2 and fine.

010

ITB unit: Thick 2 & FINE: M

*ENG

[0 to 80 / 12 / 1 A]

Adjusts the current for the image transfer belt for Magenta in full color mode for Thick 2 and fine.

011

ITB unit: Thick 2 & FINE: C

*ENG

[0 to 80 / 11 / 1 A]

Adjusts the current for the image transfer belt for Cyan in full color mode for Thick 2 and fine.

012

ITB unit: Thick 2 & FINE: Y

*ENG

[0 to 80 / 14 / 1 A]

Adjusts the current for the image transfer belt for Yellow in full color mode for Thick 2 and fine.

2360

[Common: BW Environment Correction Table]

001

Image Transfer: Plain

*ENG

[1 to 60 / 1 / 1 /step]

002

Image Transfer: Thick 1

*ENG

004

Image Transfer: Plain: Bk

*ENG

[1 to 60 / 13/ 1 /step]

005

Image Transfer: Plain: M

*ENG

[1 to 60 / 2 / 1 /step]

006

Image Transfer: Plain: C

*ENG

007

Image Transfer: Plain: Y

*ENG

008

Image Transfer: Thick 1: Bk

*ENG

[1 to 60 / 31 / 1 /step]

009

Image Transfer: Thick 1: M

*ENG

[1 to 60 / 2 / 1 /step]

010

Image Transfer: Thick 1: C

*ENG

011

Image Transfer: Thick 1: Y

*ENG

2401

[Plain: Bias]

Adjusts the DC voltage of the discharge plate for plain paper.

Plain: High speed, 1200: Low speed

001

Separation DC: Plain: 1st Side

*ENG

[0 to 4000 / 0 / 10 –V/step]

002

Separation DC: Plain: 2nd Side

*ENG

[0 to 4000 / 0 / 10 –V/step]

003

Separation DC: 1200: 1st Page

*ENG

[0 to 4000 / 0 / 10 –V/step]

004

Separation DC: 1200: 2nd side

*ENG

[0 to 4000 / 0 / 10 –V/step]

2403

[Plain: Bias: BW]

Adjusts the current for the paper transfer roller for plain paper in black-and-white mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 22 / 1 –A /step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 250 / 7 / 1 –A /step]

004

Paper Transfer: 1200: 2nd side

*ENG

[0 to 250 / 12 / 1 –A /step]

2407

[Plain: Bias: FC]

Adjusts the current for the paper transfer roller for plain paper in full color mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 27 / 1 –A /step]

002

Paper Transfer: Plain: 2nd Side

*ENG

[0 to 250 / 33 / 1 –A /step]

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 250 / 10 / 1 –A /step]

004

Paper Transfer: 1200: 2nd side

*ENG

[0 to 250 / 12 / 1 –A /step]

2411

[Plain: Paper Size Correction]

Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2403 and SP2407 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain : 1st Side: S1

*ENG

[100 to 600 / 100 / 5%/step]

S1 size > 297 mm (Paper width)

002

Paper Transfer: Plain: 2nd Side: S1

*ENG

003

Separation DC: 1200: 1st Side

*ENG

004

Separation DC: 1200: 2nd Side

*ENG

005

Paper Transfer: Plain: 1st Side: S2

*ENG

[100 to 600 / 105 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

006

Paper Transfer: Plain: 2nd Side: S2

*ENG

[100 to 600 / 120 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

007

Paper Transfer: 1200: 1st Side: S2

*ENG

[100 to 600 / 120 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

008

Paper Transfer: 1200: 2nd Side: S2

*ENG

[100 to 600 / 150 / 5%/step]

009

Paper Transfer: Plain: 1st Side: S3

*ENG

[100 to 600 / 110 / 5%/step]

275 mm > S3 size > 210 mm (Paper width)

010

Paper Transfer: Plain: 2nd Side: S3

*ENG

[100 to 600 / 140 / 5%/step]

275 mm > S3 size > 210 mm (Paper width)

011

Paper Transfer: 1200: 1st Side: S3

*ENG

012

Paper Transfer: 1200: 2nd Side: S3

*ENG

[100 to 600 / 300 / 5%/step]

013

Paper Transfer: Plain: 1st Side: S4

*ENG

[100 to 600 / 115 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

014

Paper Transfer: Plain: 2nd Side: S4

*ENG

[100 to 600 / 160 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

015

Paper Transfer: 1200: 1st Side: S4

*ENG

[100 to 600 / 240 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

016

Paper Transfer: 1200: 2nd Side: S4

*ENG

[100 to 600 / 340 / 5%/step]

017

Paper Transfer: Plain: 1st Side: S5

*ENG

[100 to 600 / 120 / 5%/step]

148 mm > S5 size (Paper width)

018

Paper Transfer: Plain: 2nd Side: S5

*ENG

[100 to 600 / 180 / 5%/step]

148 mm > S5 size (Paper width)

019

Paper Transfer: 1200: 1st Side: S5

*ENG

[100 to 600 / 300 / 5%/step]

148 mm > S5 size (Paper width)

020

Paper Transfer: 1200: 2nd Side: S5

*ENG

[100 to 600 / 400 / 5%/step]

2421

[Plain: Leading Edge Correction] Plain Paper: Leading Edge Correction

Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2403 and SP2407 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

[0 to 400 / 100 / 5%/step]

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

004

Paper Transfer: 1200: 2nd side

*ENG

2421

005-008

Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2401 is multiplied by these SPs values.

005

Separation DC: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

006

Separation DC: Plain: 2nd Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

008

Separation DC: 1200: 2nd Side

*ENG

2422

[Plain: Switch Timing: Lead. Edge]

Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

004

Paper Transfer: 1200: 2nd side

*ENG

005

Separation DC: Plain: 1st Side

*ENG

006

Separation DC: Plain: 2nd Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

008

Separation DC: 1200: 2nd Side

*ENG

2423

[Plain: Trailing Edge Correction] Plain Paper: Trailing Edge Correction

Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2403 and SP2407 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

004

Paper Transfer: 1200: 2nd side

*ENG

005

Separation DC: Plain: 1st Side

*ENG

006

Separation DC: Plain: 2nd Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

008

Separation DC: 1200: 2nd Side

*ENG

2424

[Plain: Switch Timing: Trail. Edge]

Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

004

Paper Transfer: 1200: 2nd side

*ENG

005

Separation DC: Plain: 1st Side

*ENG

006

Separation DC: Plain: 2nd Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

008

Separation DC: 1200: 2nd Side

*ENG

2430

[Plain: Environment Correction] DFU

Plain: High speed, 1200: Low speed

001

Separation DC: Plain: 1st Page

*ENG

[1 to 60 / 26 / 1 /step]

002

Separation DC: Plain: 2nd Page

*ENG

[1 to 60 / 32 / 1 /step]

003

Paper Transfer: BW: 1st Side

*ENG

[1 to 60 / 1 / 1 /step]

004

Paper Transfer: BW: 2nd Side

*ENG

[1 to 60 / 11 / 1 /step]

005

Paper Transfer: FC: 1st Side

*ENG

[1 to 60 / 39 / 1 /step]

006

Paper Transfer: FC: 2nd Side

*ENG

[1 to 60 / 14 / 1 /step]

007

Separation DC: 1200: 1st Page

*ENG

[1 to 60 / 26 / 1 /step]

008

Separation DC: 1200: 2nd side

*ENG

[1 to 60 / 32 / 1 /step]

009

Paper Transfer: 1200: BW: 1st Side

*ENG

[1 to 60 / 11 / 1 /step]

010

Paper Transfer: 1200: BW: 2

*ENG

011

Paper Transfer: 1200: FC: 1st Side

*ENG

[1 to 60 / 49 / 1 /step]

012

Paper Transfer: 1200: FC: 2

*ENG

2451

[Thin: Bias]

Adjusts the DC voltage of the discharge plate for thin paper.

Plain: High speed, 1200: Low speed

001

Separation DC: Plain: 1st Side

*ENG

[0 to 4000 / 2000 / 10 –V/step]

003

Separation DC: 1200: 1st Page

*ENG

2453

[Thin: Bias: BW]

Adjusts the current for the paper transfer roller for thin paper in black-and-white mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 22 / 1 –A /step]

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 250 / 11 / 1 –A /step]

2457

[Thin: Bias: FC]

Adjusts the current for the paper transfer roller for thin paper in full color mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 30 / 1 –A /step]

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 250 / 15 / 1 –A /step]

2461

[Thin: Paper Size Correction]

Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2453 and SP2457 are multiplied by these SP values.

Plain: High speed

001

Paper Transfer: Plain: 1st Side: S1

*ENG

[100 to 600 / 100 / 5%/step]

S1 size > 297 mm (Paper width)

005

Paper Transfer: Plain: 1st Side: S2

*ENG

[100 to 600 / 120 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

009

Paper Transfer: Plain: 1st Side: S3

*ENG

[100 to 600 / 140 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

013

Paper Transfer: Plain: 1st Side: S4

*ENG

[100 to 600 / 160 / 5%/step]

297 mm > S2 size > 275 mm (Pape r width)

017

Paper Transfer: Plain: 1st Side: S5

*ENG

[100 to 600 / 180 / 5%/step]

2471

[Thin: Leading Edge Correction] Thin Paper: Leading Edge Correction

Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2453 and SP2457 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

003

Paper Transfer: 1200: 1st Side

*ENG

2471

Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2451 is multiplied by these SP values.

005

Separation DC: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

007

Separation DC: 1200: 1st Side

*ENG

2472

[Thin: Switch Timing: Lead. Edge]

Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area.

Plain: High speed, 1200: Low speed,

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

003

Paper Transfer: 1200: 1st Side

*ENG

005

Separation DC: Plain: 1st Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

2473

[Thin: Trailing Edge Correction] Thin Paper: Trailing Edge Correction

Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2453 and SP2457 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

005

Separation DC: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

007

Separation DC: 1200: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

2474

[Thin: Switch Timing: Trail. Edge]

Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

003

Paper Transfer: 1200: 1st Side

*ENG

005

Separation DC: Plain: 1st Side

*ENG

[0 to 50 / 0 / 1 mm/step]

007

Separation DC: 1200: 1st Side

*ENG

2480

[Thin: Environment Correction]

Plain: High speed, 1200: Low speed

001

Separation DC: Plain: 1st Side

*ENG

[1 to 60 / 26 / 1 /step]

003

Paper Transfer: Plain: BW: 1st Side

*ENG

[1 to 60 / 11 / 1 /step]

005

Paper Transfer: Plain: FC: 1st Side

*ENG

[1 to 60 / 1 / 1 /step]

007

Separation DC: 1200: 1st Side

*ENG

[1 to 60 / 26 / 1 /step]

009

Paper Transfer: 1200: BW: 1st Side

*ENG

[1 to 60 / 11 / 1 /step]

011

Paper Transfer: 1200: FC: 1st Side

*ENG

[1 to 60 / 1 / 1 /step]

2481

[Glossy: Bias]

001

Separation DC: Glossy: 1st Side

*ENG

[0 to 4000 / 2000 / 10 –V/step]

Adjusts the DC voltage of the discharge plate for glossy paper.

2482

[Glossy: Bias: BW]

001

Paper Transfer: Glossy: 1st Side

*ENG

[0 to 250 / 12 / 1 –A /step]

Adjusts the current for the paper transfer roller for glossy paper in black-and-white mode.

2483

[Glossy: Bias: FC]

001

Paper Transfer: Glossy: 1st Side

*ENG

[0 to 250 / 15 / 1 –A /step]

Adjusts the current for the paper transfer roller for glossy paper in full color mode.

2484

[Glossy: Paper Size Correction]

001

Paper Transfer: Glossy: 1st Side: S1

*ENG

[100 to 600 / 100 / 5%/step]

005

Paper Transfer: Glossy: 1st Side: S2

*ENG

[100 to 600 / 120 / 5%/step]

009

Paper Transfer: Glossy: 1st Side: S3

*ENG

[100 to 600 / 140 / 5%/step]

013

Paper Transfer: Glossy: 1st Side: S4

*ENG

[100 to 600 / 160 / 5%/step]

017

Paper Transfer: Glossy: 1st Side: S5

*ENG

[100 to 600 / 180 / 5%/step]

2485

[Glossy: Leading Edge Correction]

001

Paper Transfer: 1st Side

*ENG

[10 to 400 / 100 / 5%/step]

005

Separation DC: 1st Side

*ENG

[10 to 400 / 100 / 5%/step]]

2486

[Glossy: Switch Timing: Lead. Edge]

001

Paper Transfer: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

005

Separation DC: 1st Side

*ENG

2487

[Glossy: Trailing Edge Correction]

001

Paper Transfer: 1st Side

*ENG

[0 to 400 / 100 / 5 %/step]

005

Separation DC: 1st Side

*ENG

2488

[Glossy: Switch Timing: Trail. Edge]

001

Paper Transfer: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

005

Separation DC: 1st Side

*ENG

2489

[Glossy: Environment Correction]

001

Separation DC: 1st Side

*ENG

[1 to 60 / 26 / 1 /step]

003

Paper Transfer: BW: 1st Side

*ENG

[1 to 60 / 11 / 1 /step]

005

Paper Transfer: FC: 2nd Side

*ENG

[1 to 60 / 1 / 1 /step]

2501

[Thick 1: Bias]

Adjusts the DC voltage of the discharge plate for thick 1 paper.

Plain: High speed, 1200: Low speed

001

Separation DC: Plain: 1st Side

*ENG

[0 to 4000 / 1000 / 10 –V/step]

002

Separation DC: Plain: 2nd Side

*ENG

003

Separation DC: 1200: 1st Side

*ENG

2502

[Thick 1: Bias: BW]

Adjusts the current for the paper transfer roller for thick 1 paper in black-and-white mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 24 / 1 –A /step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Separation DC: 1200: 1st Side

*ENG

[0 to 250 / 12 / 1 –A /step]

2507

[Thick 1: Bias: FC]

Adjusts the current for the paper transfer roller for thick 1 paper in full color mode.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 250 / 30 / 1 –A /step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Separation DC: 1200: 1st Side

*ENG

[0 to 250 / 15 / 1 –A /step]

2511

[Thick 1: Paper Size Correction]

Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2502 and SP2507 are multiplied by these SP values.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side: S1

*ENG

[100 to 600 / 100 / 5%/step]

S1 size > 297 mm (Paper width)

002

Paper Transfer: Plain: 2nd Side: S1

*ENG

003

Paper Transfer: 1200: 1st Side: S1

*ENG

[100 to 600 / 100 / 5%/step]

S1 size > 297 mm (Paper width)

005

Paper Transfer: Plain: 1st Side: S2

*ENG

[100 to 600 / 105 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

006

Paper Transfer: Plain: 2nd Side: S2

*ENG

[100 to 600 / 130 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

007

Paper Transfer: 1200: 1st Side: S2

*ENG

[100 to 600 / 120 / 5%/step]

297 mm > S2 size > 275 mm (Paper width)

009

Paper Transfer: Plain: 1st Side: S3

*ENG

[100 to 600 / 110 / 5%/step]

275 mm > S3 size > 210 mm (Paper width)

010

Paper Transfer: Plain: 2nd Side: S3

*ENG

[100 to 600 / 160 / 5%/step]

275 mm > S3 size > 210 mm (Paper width)

011

Paper Transfer: 1200: 1st Side: S3

*ENG

[100 to 600 / 140 / 5%/step]

275 mm > S3 size > 210 mm (Paper width)

013

Paper Transfer: Plain 1: 1st Side: S4

*ENG

[100 to 600 / 115 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

014

Paper Transfer: Plain: 2nd Side: S4

*ENG

[100 to 600 / 190 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

015

Paper Transfer: 1200: 1st Side: S4

*ENG

[100 to 600 / 160 / 5%/step]

210 mm > S4 size > 148 mm (Paper width)

017

Paper Transfer: Plain 1: 1st Side: S5

*ENG

[100 to 600 / 120 / 5%/step]

148 mm > S5 size (Paper width)

018

Paper Transfer: Plain: 2nd Side: S5

*ENG

[100 to 600 / 220 / 5%/step]

148 mm > S5 size (Paper width)

019

Paper Transfer: 1200: 1st Side: S5

*ENG

[100 to 600 / 180 / 5%/step]

148 mm > S5 size (Paper width)

2521

[Thick 1: Leading Edge Correction] Thick 1 Paper: Leading Edge Correction

Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2502 and SP2507 are multiplied by these SP values.

Thick 1: Middle speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

005

Separation DC: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

006

Separation DC: Plain: 2nd Side

*ENG

007

Separation DC: 1200: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

2522

[Thick 1: Switch Timing: Lead. Edge]

Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area.

Thick 1: Middle speed, 1200: Low speed

001

Paper Transfer: Thick 1: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

002

Paper Transfer: Thick 1: 2nd Side

*ENG

005

Separation DC: Thick 1: 1st Side

*ENG

[0 to 50 / 0 / 2 mm/step]

006

Separation DC: Thick 1: 2nd Side

*ENG

2523

[Thick 1: Trailing Edge Correction] Thick 1 Paper: Trailing Edge Correction

Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2502 and SP2507 are multiplied by these SP values.

Thick 1: Middle speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 400 / 100 / 5%/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

005

Paper Transfer: Plain: 1st Side

*ENG

006

Paper Transfer: Plain: 2nd Side

*ENG

[0 to 400 / 100 / 5%/step]

007

Paper Transfer: 1200: 1st Side

*ENG

2524

[Thick 1: Switch Timing: Trail. Edge]

Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area.

Plain: High speed, 1200: Low speed

001

Paper Transfer: Plain: 1st Side

*ENG

[0 to 50 / 0 / 1 mm/step]

002

Paper Transfer: Plain: 2nd Side

*ENG

003

Paper Transfer: 1200: 1st Side

*ENG

005

Paper Transfer: Plain: 1st Side

*ENG

006

Paper Transfer: Plain: 2nd Side

*ENG

007

Paper Transfer: 1200: 1st Side

*ENG

2530

[Thick 1: Environment Correction]

Plain: High speed, 1200: Low speed

001