SP6-XXX (Peripherals)

6006

[ADF Adj.] ADF Adjustment

Adjusts the side-to-side and leading registration of originals with the ARDF.

001

Side-to-Side Registration

*ENG

[-3.0 to 3.0 / 0 / 0.1 mm/step ]

002

Side-to-Side Registration (2nd side)

003

Leading Edge Registration

[-5.0 to 5.0 / 0 / 0.1 mm/step ]

Adjusts the amount of paper buckle to correct original skew for the front and rear sides.

005

Buckle: Duplex Front

*ENG

[-3.0 to 3.0 / 0 / 0.1 mm/step ]

006

Buckle: Duplex Rear

[-2.5 to 2.5 / 0 / 0.1 mm/step ]

Adjusts the erase margin at the original trailing edge.

007

Rear Edge Erase

*ENG

[-10 to 10 / 0 / 0.1 mm/step ]

6007

[ADF Input Check]

Displays the signals received from the sensors and switches of the ARDF. Only Bit 0 is used for ADF input check ( Input and Output Check).

6008

[ADF Output Check]

Activates the electrical components for functional check.

It is not possible to activate more than one component at the same time ( Input and Output Check).

6009

[ADF Free Run]

Performs a DF free run in simplex, duplex mode or stamp mode.

001

Free Run Simplex Motion

-

-

002

Free Run Duplex Motion

-

003

Free Run Stamp Motion

-

6010

[Stamp Position Adj.] Fax Stamp Position Adjustment

Adjusts the horizontal position of the stamp on the scanned originals.

6010 1

Stamp Position Adj.

*ENG

[-5.0 to 5.0 / 0 / 1 mm/step]

6011

[1-Pass ADF INPUT Check] Not used

6012

[1-Pass ADF OUTPUT Check] Not used

6016

[Original Size Detection Priority] Original Size Detection Priority

Specifies the original size for a size detected by the original sensor, since original sensors cannot recognize all sizes.

001

Original Size Detection Priority

*ENG

[0 or 1 / 0 / - ]

0: Setting 1, 1: Setting 2

NA

Setting 1

Setting 2

DLT SEF

Folio SEF 11" x 15"

LG SEF

Foolscap SEF

LT SEF

US EXE 8" x 10"

LT LEF

US EXE LEF

EU/

ASIA

DLT SEF

8K 267 x 390 mm

LT SEF

16K 195 x 267 mm

LT LEF

16K 267 x 195 mm

6017

[DF Magnification Adj.] DF Magnification Adjustment

Adjusts the magnification in the sub-scan direction for the ARDF.

001

DF Magnification Adj.

*CTL

[-5.0 to 5.0 / 0 / 0.1 %/step]

6020

[Skew Correction Moving Setting]

Turns the original skew correction in the ARDF for all original sizes on or off.

001

-

*ENG

[0 or 1 / 0 / - ]

0: Off (only for small original sizes)

1: On (for all original sizes)

6128

[Punch Position: Sub Scan]

Adjusts the punching position in the sub scan direction.

001

Domestic (Japan) 2Hole

*ENG

[-7.5 to 7.5 / 0 / 0.5 mm/step]]

002

North America 3Hole

*ENG

003

Europe 4Hole

*ENG

004

North Europe 4Hole

*ENG

005

North Europe 2Hole

*ENG

6129

[Punch Position: Main Scan]

Adjusts the punching position in the main scan direction.

001

Domestic (Japan) 2Hole

*ENG

[-2.0 to 2.0 / 0 / 0.4 mm/step]]

002

North America 3Hole

*ENG

003

Europe 4Hole

*ENG

004

North Europe 4Hole

*ENG

005

North Europe 2Hole

*ENG

6130

[Skew Correction: Buckle Adj.]

Adjusts the paper buckle for each paper size.

001

A3T

*ENG

[-5.0 to 5.0 / 0 / 0.25 mm/step]]

002

B4T

*ENG

003

A4T

*ENG

004

A4Y

*ENG

005

B5T

*ENG

006

B5Y

*ENG

007

DLT-T

*ENG

008

LG-T

*ENG

009

LT-T

*ENG

010

LT-Y

*ENG

011

12" x 18"

*ENG

012

Other

*ENG

6131

[Skew Correction Control]

Selects the skew correction control for each paper size. These are only activated for B793.

001

A3T

*ENG

[0 or 1 / 1 / 1/step]]

0: No (No skew correction)

1: Roller Stop Skew Correction

002

B4T

*ENG

003

A4T

*ENG

004

A4Y

*ENG

005

B5T

*ENG

006

B5Y

*ENG

007

DLT-T

*ENG

008

LG-T

*ENG

009

LT-T

*ENG

010

LT-Y

*ENG

011

12" x 18"

*ENG

012

Other

*ENG

6132

[Jogger Fence Fine Adj]

This SP adjusts the distance between the jogger fences and the sides of the stack on the finisher stapling tray in the Booklet Finisher B793. The adjustment is done perpendicular to the direction of paper feed.

001

A3T

*ENG

[-1.5 to 1.5 / 0 / 0.5 mm/step]

+ Value: Increases distance between jogger fences and the sides of the stack.

- Value: Decreases the distance between the jogger fences and the sides of the stack.

002

B4T

*ENG

003

A4T

*ENG

004

A4Y

*ENG

005

B5T

*ENG

006

B5Y

*ENG

007

DLT-T

*ENG

008

LG-T

*ENG

009

LT-T

*ENG

010

LT-Y

*ENG

011

12" x 18"

*ENG

012

Other

*ENG

6133

[Staple Position Adjustment]

Adjusts the staple position for each finisher (B408/B793/D372).

+ Value: Moves the staple position to the rear side.

- Value: Moves the staple position to the front side.

001

Finisher (B408/B793)

*ENG

[-3.5 to 3.5 / 0 / 1/step]

6134

[Saddle Stitch Position Adjustment]

User SP

Use this SP to adjust the stapling position of the booklet stapler when paper is stapled and folded in the Booklet Finisher B793.

001

A3T

[-3.0 to 3.0 / 0 / 0.2 mm/step]

+ Value: Shifts staple position toward the crease.

- Value: Shifts staple position away from the crease.

002

B4T

003

A4T

004

B5T

005

DLT-T

006

LG-T

007

LT-T

008

12" x 18"

009

Other

6135

[Folder Position Adj.]

User SP

This SP corrects the folding position when paper is stapled and folded in the Booklet Finisher B793.

001

A3T

[-3.0 to 3.0 / 0 / 0.2 mm/step]

+ Value: Shifts staple position toward the crease.

- Value: Shifts staple position away from the crease.

002

B4T

003

A4T

004

B5T

005

DLT-T

006

LG-T

007

LT-T

008

12" x 18"

009

Other

6136

[Folding Number]

User SP

Sets the number of times that folding is done in the Booklet Finisher B793.

001

-

[2 to 30 / 2 / 1 time/step]

6137

[Finisher Free Run]

These SPs are used only for B793 finisher.

001

Free Run 1

Free run for paper edge stapling.

002

Free Run 2

Free run for booklet stapling.

003

Free Run 3

Shipping free run. Simulates standby conditions during shipping.

004

Free Run 4

DFU

6138

[FIN (TIG) INPUT Check] Finisher (B793) Input Check

Displays the signals received from sensors and switches of the booklet finisher. ( Input and Output Check)

6139

[FIN (KIN) INPUT Check] Finisher (B408) Input Check

Displays the signals received from sensors and switches of the booklet finisher. ( Input and Output Check)

6140

[FIN (EUP) INPUT Check] Not used

6141

[FIN (ELB) INPUT Check] Finisher (D372) Input Check

Displays the signals received from sensors and switches of the booklet finisher. ( Input and Output Check)

6143

[FIN (TIG) OUPUT Check] Finisher (B793) Output Check

Displays the signals received from sensors and switches of the booklet finisher. ( Input and Output Check)

6144

[FIN (KIN) OUPUT Check] Finisher (B408) Output Check

Displays the signals received from sensors and switches of the booklet finisher. ( Input and Output Check)

6145

[FIN (EUP) OUPUT Check] Not used

6146

[FIN (ELB) OUPUT Check] Finisher (D372) Output Check

Displays the signals received from sensors and switches of the 500-sheet finisher. ( Input and Output Check)

6149

[Max. Pre-Stack Sheet]

*ENG

Number of Pre-Stack Sheets

This SP sets the number of sheets sent to the pre-stack tray.

Note:

You may need to adjust this setting or switch it off when feeding thick or slick paper.

001

-

[0 to 3 / 3 / 1 sheet/step]

6150

[INPUT Check]

Displays the signals received from sensors and switches of the bridge unit (D386)/ side tray (D542) ( Input and Output Check).

6151

[OUTPUT Check]

Displays the signals received from sensors and switches of the bridge unit (D386)/ side tray (D542) ( Input and Output Check).

6152

[INPUT Check]

Displays the signals received from sensors and switches of the shift tray (D388) ( Input and Output Check).

6153

[OUTPUT Check]

Displays the signals received from sensors and switches of the shift tray (D388) ( Input and Output Check).

6154

[INPUT Check]

Displays the signals received from sensors and switches of the 1 bin tray (D536) ( Input and Output Check).

6155

[OUTPUT Check]

Displays the signals received from sensors and switches of the 1 bin tray (D414) ( Input and Output Check).

001

1 bin: Junction Solenoid

6157

[OUTPUT Check]

Not used in this machine

6160

[INPUT Check]

Displays the signals received from sensors and switches of the two-tray paper feed unit (D537), LCT 2000 (D538) and LCT 1200 (D539) ( Input and Output Check).

6161

[OUTPUT Check]

Displays the signals received from sensors and switches of the two-tray paper feed unit (D537), LCT 2000 (D538) and LCT 1200 (D539) ( Input and Output Check).

6801

[1-pass Stamp Unit] Not used

6830

[Extra Staples] Not used

6900

[ADF Bottom Plate Setting]

This SP setting determines whether the bottom plate lift motor of the of the ADF switches on:

001

A3T

*ENG

[0 or 1 / 0 / -]

0: Bottom plate lifts immediately after originals are set (Default)

1: Bottom plate does not lift until [Start] key is pushed.