2005 |
[Charge DC Voltage] Charge Roller DC Voltage Adjustment (Paper Type, Process Speed, Color) Paper Type –> Plain, Thick 1, Thick 2 Plain: High speed, Thick 1: Middle speed, Thick 2&FINE: Low speed |
||
Adjusts the DC component of the charge roller bias in the various print modes. Charge bias (DC component) is automatically adjusted during process control; therefore, adjusting these settings does not effect while process control mode (SP3-041-1 Default: ON) is activated. When deactivating process control mode with SP3-041-1, the values in these SP modes are used for printing. |
|||
001 |
Plain: Bk |
*ENG |
[0 to 1000 / 690 / 10 –V/step] |
002 |
Plain: M |
*ENG |
|
003 |
Plain: C |
*ENG |
|
004 |
Plain: Y |
*ENG |
|
005 |
Thick 1: Bk |
*ENG |
|
006 |
Thick 1: M |
*ENG |
|
007 |
Thick 1: C |
*ENG |
|
008 |
Thick 1: Y |
*ENG |
|
009 |
Thick 2&FINE: Bk |
*ENG |
|
010 |
Thick 2&FINE: M |
*ENG |
|
011 |
Thick 2&FINE: C |
*ENG |
|
012 |
Thick 2&FINE: Y |
*ENG |
|
[Charge DC: Correction] |
|||
013 |
PCU:Plain |
*ENG |
[–100 to 100 / -29 / 1 –V/step] |
014 |
PCU:Thick 1 |
*ENG |
[–100 to 100 / -28 / 1 –V/step] |
015 |
PCU:Thick 2&FINE |
*ENG |
[–100 to 100 / -28 / 1 –V/step] |
016 |
HVP:Plain |
*ENG |
[–100 to 100 / 20 / 1 –V/step] |
017 |
HVP:Thick 1 |
*ENG |
[–100 to 100 / 20 / 1 –V/step] |
018 |
HVP: Thick 2&FINE |
*ENG |
[–100 to 100 / 29 / 1 –V/step] |
2006 |
[Charge AC Voltage] Charge Roller AC Voltage Adjustment (Paper Type, Process Speed, Color) Paper Type –> Plain, Thick 1, Thick 2 Plain: High speed, Thick 1: Middle speed, Thick 2&FINE: Low speed |
||
Adjusts the AC component of the charge roller bias in the various print modes. Charge bias (AC component) is adjusted by environment correction (SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1 is set to "1: manual control". |
|||
001 |
Plain: Bk |
*ENG |
[0 to 3 / 1.9 / 0.01 KV/step] |
002 |
Plain: M |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
003 |
Plain: C |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
004 |
Plain: Y |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
005 |
Thick 1: Bk |
*ENG |
[0 to 3 / 1.9 / 0.01 KV/step] |
006 |
Thick 1: M |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
007 |
Thick 1: C |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
008 |
Thick 1: Y |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
009 |
Thick 2&FINE: Bk |
*ENG |
[0 to 3 / 1.9 / 0.01 KV/step] |
010 |
Thick 2&FINE: M |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
011 |
Thick 2&FINE: C |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
012 |
Thick 2&FINE: Y |
*ENG |
[0 to 3 / 2.2 / 0.01 KV/step] |
2012 |
[Charge Output Control] |
||
001 |
AC Voltage |
*ENG |
Selects the AC voltage control type. [0 or 1 / 0 / 1 /step] 0: Process control 1: Manual control (AC voltages are decided with SP2006.) |
2013 |
[Environmental Correction: PCU] |
||
001 |
Current Environmental: Display |
*ENG |
Displays the environmental condition, which is measured in absolute humidity. [1 to 5 / – / 1 /step] 1: LL (LL <= 4.3 g/m3) 2: ML (4.3 < ML <= 11.3 g/m3) 3: MM (11.3 < MM <= 18.0 g/m3) 4: MH (18.0 < MH <= 24.0 g/m3) 5: HH (24.0 g/m3 < HH) |
002 |
Forced Setting |
*ENG |
Selects the environmental condition manually. [0 to 5 / 0 / 1 /step] 0: The environmental condition is determined automatically. 1: LL, 2: ML, 3: MM, 4: MH, 5: HH |
003 |
Absolute Humidity: Threshold 1 |
*ENG |
Changes the humidity threshold between LL and ML. [0 to 100 / 3.0 / 0.01 g/m3/step] |
004 |
Absolute Humidity: Threshold 2 |
*ENG |
Changes the humidity threshold between ML and MM. [0 to 100 / 8.0 / 0.01 g/m3/step] |
005 |
Absolute Humidity: Threshold 3 |
*ENG |
Changes the humidity threshold between MM and MH. [0 to 100 / 15.0 / 0.01 g/m3/step] |
006 |
Absolute Humidity: Threshold 4 |
*ENG |
Changes the humidity threshold between MH and HH. [0 to 100 / 15.0 / 0.01 g/m3/step] |
007 |
Current Temp.: Display |
*ENG |
Displays the current temperature. [0 to 100 / 0 / 1 deg/step] |
008 |
Current Relative Humidity: Display |
*ENG |
Displays the current relative humidity. [0 to 100 / 0 / 1%RH/step] |
009 |
Current Absolute Humidity: Display |
*ENG |
Displays the absolute humidity. [0 to 100 / 0 / 0.01 g/m3/step] |
010 |
Previous Environmental: Display |
*ENG |
Displays the previous environmental condition, which is measured in absolute humidity. [1 to 5 / – / 1 /step] 1: LL, 2: ML, 3: MM, 4: MH, 5: HH |
011 |
Previous Temp.: Display |
*ENG |
Displays the previous temperature. [0 to 100 / 0 / 1 deg/step] |
012 |
Previous Relative Humidity: Display |
*ENG |
Displays the previous relative humidity. [0 to 100 / 0 / 1%RH/step] |
013 |
Previous Absolute Humidity: Display |
*ENG |
Displays the previous absolute humidity. [0 to 100 / 0 / 0.01 g/m3/step] |
2015 |
[Charge AC Adj: Result] |
||
001 |
Bk |
*ENG |
[0 to 9 / 0 / 1 /step] 0: Success 1: Out of tolerance range 2: Out of adjustable range 3: Adjustment incompleted |
002 |
M |
*ENG |
|
003 |
C |
*ENG |
|
004 |
Y |
*ENG |
2101 |
[Color Registration Correction] FA |
||
These values are the parameters for the automatic line position adjustment and are adjusted at the factory. However, you must input a value for SP2101-001 after replacing the laser optics housing unit. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section. The value should be provided with the new laser optics housing unit. |
|||
001 |
Main Dot: Bk |
*ENG |
[–512 to 511 / 0 / 1 dot/step] |
002 |
Main Dot: Ma |
*ENG |
|
003 |
Main Dot: Cy |
*ENG |
|
004 |
Main Dot: Ye |
*ENG |
|
005 |
Sub Line: Bk |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
006 |
Sub Line: Ma |
*ENG |
|
007 |
Sub Line: Cy |
*ENG |
|
008 |
Sub Line: Ye |
*ENG |
2103 |
[Erase Margin Adjustment] (Area, Paper Size) |
||
Adjusts the erase margin by deleting image data at the margins. |
|||
001 |
Lead Edge Width |
*ENG |
[0 to 9.9 / 4.2 / 0.1 mm/step] |
002 |
Trail. Edge Width |
*ENG |
|
003 |
Left |
*ENG |
[0 to 9.9 / 2 / 0.1 mm/step] |
004 |
Right |
*ENG |
|
006 |
Duplex Trail. L Size |
*ENG |
[0 to 4 / 1 / 0.1 mm/step] |
007 |
Duplex Trail. M Size |
*ENG |
[0 to 4 / 0.8 / 0.1 mm/step] |
008 |
Duplex Trail. S Size |
*ENG |
[0 to 4 / 0.6 / 0.1 mm/step] |
009 |
Duplex Left Edge |
*ENG |
[0 to 1.5 / 0.3 / 0.1 mm/step] |
010 |
Duplex Right Edge |
*ENG |
|
011 |
Duplex Trail. L Size:Thick |
*ENG |
[0 to 4 / 1 / 0.1 mm/step] |
012 |
Duplex Trail. M Size:Thick |
*ENG |
[0 to 4 / 0.8 / 0.1 mm/step] |
013 |
Duplex Trail. S Size:Thick |
*ENG |
[0 to 4 / 0.6 / 0.1 mm/step] |
014 |
Duplex Left Edge:Thick |
*ENG |
[0 to 1.5 / 0.3 / 0.1 mm/step] |
015 |
Duplex Right Edge:Thick |
*ENG |
2105 |
[LD Power Adj.] (Process Speed, Color) |
||
Adjusts the LD power of each color for each process speed. Each LD power setting is decided by process control. |
|||
001 |
High Speed: Bk |
*ENG |
[50 to 120 / 100 / 1%/step] Decreasing a value makes lines thinner on the output. Increasing a value makes lines thicker on the output. |
002 |
High Speed: Ma |
*ENG |
|
003 |
High Speed: Cy |
*ENG |
|
004 |
High Speed: Ye |
*ENG |
|
005 |
Middle Speed: Bk |
*ENG |
[50 to 120 / 100 / 1%/step] Decreasing a value makes lines thinner on the output. Increasing a value makes lines thicker on the output. |
006 |
Middle Speed: Ma |
*ENG |
|
007 |
Middle Speed: Cy |
*ENG |
|
008 |
Middle Speed: Ye |
*ENG |
|
009 |
Low Speed: Bk |
*ENG |
[50 to 120 / 100 / 1%/step] Decreasing a value makes lines thinner on the output. Increasing a value makes lines thicker on the output. |
010 |
Low Speed: Ma |
*ENG |
|
011 |
Low Speed: Cy |
*ENG |
|
012 |
Low Speed: Ye |
*ENG |
2109 |
[Test Pattern] |
||
Generates the test pattern using "COPY Window" tab in the LCD. |
|||
003 |
Pattern Selection |
- |
[0 to 23 / 0 / 1/step] |
0 None 1: Vertical Line (1dot) 2: Vertical Line (2dot) 3: Horizontal (1dot) 4: Horizontal (2dot) 5: Grid Vertical Line 6: Grid Horizontal Line 7: Grid pattern Small 8: Grid pattern Large 9: Argyle Pattern Small 10: Argyle Pattern Large |
11. Independent Pattern (1dot) 12. Independent Pattern (2dot) 13. Independent Pattern (4dot) 14. Trimming Area 16: Hound’s Tooth Check (Horizontal) 17: Band (Horizontal) 18: Band (Vertical) 19: Checker Flag Pattern 20: Grayscale Vertical Margin 21: Grayscale Horizontal Margin 23: Full Dot Pattern |
||
005 |
Color Selection |
- |
Specifies the color for the test pattern. [1 to 4 / 1 / 1/step] 1: All colors, 2: Magenta, 3: Yellow, 4: Cyan |
006 |
Density: Bk |
- |
Specifies the color density for the test pattern. [0 to 15 / 15 / 1 /step] 0: Lightest density 15: Darkest density |
007 |
Density: Ma |
- |
|
008 |
Density: Cy |
- |
|
009 |
Density: Ye |
- |
2111 |
[Forced Line Position Adj.] |
||
001 |
Mode a |
- |
Executes the fine line position adjustment twice. If this SP is not completed (NG is displayed), do SP2111-003 first and then try this SP again. |
002 |
Mode b |
- |
Executes the fine line position adjustment once. If this SP is not completed, do SP2111-003 first and then try this SP again. |
003 |
Mode c |
- |
Executes the rough line position adjustment once. After doing this SP, make sure to execute SP2111-001 or -002. Otherwise, the line position adjustment is not perfectly done. |
2112 |
[TM/ID Sensor Check] ID Sensor Check FA |
||
001 |
Execute |
[0 or 1 / 0 / 1 /step] This SP is used to check the ID sensors at the factory. The results of this SP are displayed in SP2140 to SP2145. |
2117 |
[Skew Adjustment] |
||
Specifies a skew adjustment value for the skew motor M, C or Y. These SPs must be used when a new laser optics housing unit is installed or when SC2.585 occurs. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section. |
|||
001 |
Pulse: M |
*ENG |
[–50 to 50 / 0 / 1 pulse/step] |
002 |
Pulse: C |
*ENG |
|
003 |
Pulse: Y |
*ENG |
2118 |
[Skew Adjustment] |
||
001 |
Execute: M |
*ENG |
Changes the current skew adjustment values to the values specified with SP2117. These SPs must be used when a new laser optics housing unit is installed or when SC2.585 occurs. For details, see "Laser Optics Housing Unit" in the "Replacement and Adjustment" section. |
002 |
Execute: C |
*ENG |
|
003 |
Execute: Y |
*ENG |
2119 |
[Skew Adjustment Display] |
||
Displays the current skew adjustment value for each skew motor. |
|||
001 |
M |
*ENG |
[–50 to 50 / 0 / 1 pulse/step] |
002 |
C |
*ENG |
|
003 |
Y |
*ENG |
2150 |
[Area Mag. Correction] LD Pulse Area Correction (Color, Area) FA |
||
Adjusts the magnification for each area. The main scan (297 mm) is divided into 8 areas. Area 1 is at the front side of the machine (left side of the image) and area 8 is at the rear side of the machine (right side of the image). Decreasing a value makes the image shift to the left side on the print. Increasing a value makes the image shift to the right side on the print. 1 pulse = 1/16 dot |
|||
027 |
Area 0: Bk |
*ENG |
[-256 to 255 / 0 / 1sub-dot/step] |
028 |
Area 1: Bk |
*ENG |
Adjusts the area magnification for LD 0. [–256 to 255 / 0 / 1 sub-dot/step ] |
029 |
Area 2: Bk |
*ENG |
|
030 |
Area 3: Bk |
*ENG |
|
031 |
Area 4: Bk |
*ENG |
|
032 |
Area 5: Bk |
*ENG |
|
033 |
Area 6: Bk |
*ENG |
|
034 |
Area 7: Bk |
*ENG |
|
035 |
Area 8: Bk |
*ENG |
|
036 |
Area 9: Bk |
*ENG |
Not used |
037 |
Area 10: Bk |
*ENG |
|
038 |
Area 11: Bk |
*ENG |
|
039 |
Area 12: Bk |
*ENG |
|
079 |
Area 0: Ma |
*ENG |
Not used |
080 |
Area 1: Ma |
*ENG |
Adjusts the area magnification for LD 0. [–255to 255 / 0 / 1 sub-dot/step] |
081 |
Area 2: Ma |
*ENG |
[–256to 255 / 0 / 1 sub-dot/step] |
082 |
Area 3: Ma |
*ENG |
|
083 |
Area 4: Ma |
*ENG |
|
084 |
Area 5: Ma |
*ENG |
|
085 |
Area 6: Ma |
*ENG |
|
086 |
Area 7: Ma |
*ENG |
|
087 |
Area 8: Ma |
*ENG |
|
088 |
Area 9: Ma |
*ENG |
Not used |
089 |
Area 10: Ma |
*ENG |
|
090 |
Area 11: Ma |
*ENG |
|
091 |
Area 12: Ma |
*ENG |
|
131 |
Area 0: Cy |
*ENG |
Not used |
132 |
Area 1: Cy |
*ENG |
Adjusts the area magnification for LD 0. [–256 to 255 / 0 / 1 sub-dot/step] |
133 |
Area 2: Cy |
*ENG |
|
134 |
Area 3: Cy |
*ENG |
|
135 |
Area 4: Cy |
*ENG |
|
136 |
Area 5: Cy |
*ENG |
|
137 |
Area 6: Cy |
*ENG |
|
138 |
Area 7: Cy |
*ENG |
|
139 |
Area 8: Cy |
*ENG |
|
140 |
Area 9: Cy |
*ENG |
Not used |
141 |
Area 10: Cy |
*ENG |
|
142 |
Area 11: Cy |
*ENG |
|
143 |
Area 12: Cy |
*ENG |
|
183 |
Area 0: Ye |
*ENG |
Not used |
184 |
Area 1: Ye |
*ENG |
Adjusts the area magnification for LD 0. [–256 to 255 / 0 / 1 sub-dot/step] |
185 |
Area 2: Ye |
*ENG |
|
186 |
Area 3: Ye |
*ENG |
|
187 |
Area 4: Ye |
*ENG |
|
188 |
Area 5: Ye |
*ENG |
|
189 |
Area 6: Ye |
*ENG |
|
190 |
Area 7: Ye |
*ENG |
|
191 |
Area 8: Ye |
*ENG |
|
192 |
Area 9: Ye |
*ENG |
Not used |
193 |
Area 10: Ye |
*ENG |
|
194 |
Area 11: Ye |
*ENG |
|
195 |
Area 12: Ye |
*ENG |
2152 |
[Area Shad. Correct. Setting] FA |
||
Adjusts the area correction value for each LD power. The main scan is divided into 16 areas. However, the image areas are limited from area 1 to area 14. For BK and Magenta, area 1 is at the rear side of the machine (left side of the image) and area 14 is at the front side of the machine (right side of the image). For Cyan and Yellow, area 1 is at the front side of the machine (right side of the image) and area 14 is at the rear side of the machine (left side of the image). |
|||
001 |
Area 0: Bk |
*ENG |
This is for the synchronizing detection board. [50 to 150 / 100 / 1 %/step] |
002 |
Area 1: Bk |
*ENG |
|
003 |
Area 2: Bk |
*ENG |
|
004 |
Area 3: Bk |
*ENG |
|
005 |
Area 4: Bk |
*ENG |
|
006 |
Area 5: Bk |
*ENG |
|
007 |
Area 6: Bk |
*ENG |
|
008 |
Area 7: Bk |
*ENG |
|
009 |
Area 8: Bk |
*ENG |
|
010 |
Area 9: Bk |
*ENG |
|
011 |
Area 10: Bk |
*ENG |
|
012 |
Area 11: Bk |
*ENG |
|
013 |
Area 12: Bk |
*ENG |
|
014 |
Area 13: Bk |
*ENG |
|
015 |
Area 14: Bk |
*ENG |
|
016 |
Area 15: Bk |
*ENG |
This is out of the image area. [50 to 150 / 100 / 1 %/step] |
033 |
Area 0: M |
*ENG |
This is for the synchronizing detection board. |
034 |
Area 1: M |
*ENG |
[50 to 150 / 100 / 1 %/step] |
035 |
Area 2: M |
*ENG |
|
036 |
Area 3: M |
*ENG |
|
037 |
Area 4: M |
*ENG |
|
038 |
Area 5: M |
*ENG |
|
039 |
Area 6: M |
*ENG |
|
040 |
Area 7: M |
*ENG |
|
041 |
Area 8: M |
*ENG |
|
042 |
Area 9: M |
*ENG |
|
043 |
Area 10: M |
*ENG |
|
044 |
Area 11: M |
*ENG |
|
045 |
Area 12: M |
*ENG |
|
046 |
Area 13: M |
*ENG |
|
047 |
Area 14: M |
*ENG |
|
048 |
Area 15: M |
*ENG |
This is out of the image area. [50 to 150 / 100 / 1 %/step] |
065 |
Area 0: C |
*ENG |
This is for the synchronizing detection board. [50 to 150 / 100 / 1 %/step] |
066 |
Area 1: C |
*ENG |
[50 to 150 / 100 / 1 %/step] |
067 |
Area 2: C |
*ENG |
|
068 |
Area 3: C |
*ENG |
|
069 |
Area 4: C |
*ENG |
|
070 |
Area 5: C |
*ENG |
|
071 |
Area 6: C |
*ENG |
|
072 |
Area 7: C |
*ENG |
|
073 |
Area 8: C |
*ENG |
|
074 |
Area 9: C |
*ENG |
|
075 |
Area 10: C |
*ENG |
|
076 |
Area 11: C |
*ENG |
|
077 |
Area 12: C |
*ENG |
|
078 |
Area 13: C |
*ENG |
|
079 |
Area 14: C |
*ENG |
|
080 |
Area 15: C |
*ENG |
This is out of the image area. [50 to 150 / 100 / 1 %/step] |
097 |
Area 0: Y |
*ENG |
This is for the synchronizing detection board. [50 to 150 / 100 / 1 %/step] |
098 |
Area 1: Y |
*ENG |
[50 to 150 / 100 / 1 %/step] |
099 |
Area 2: Y |
*ENG |
|
100 |
Area 3: Y |
*ENG |
|
101 |
Area 4: Y |
*ENG |
|
102 |
Area 5: Y |
*ENG |
|
103 |
Area 6: Y |
*ENG |
|
104 |
Area 7: Y |
*ENG |
|
105 |
Area 8: Y |
*ENG |
|
106 |
Area 9: Y |
*ENG |
|
107 |
Area 10: Y |
*ENG |
|
108 |
Area 11: Y |
*ENG |
|
109 |
Area 12: Y |
*ENG |
|
110 |
Area 13: Y |
*ENG |
|
111 |
Area 14: Y |
*ENG |
|
112 |
Area 15: Y |
*ENG |
This is out of the image area. |
2160 |
[Vertical Line Width] DFU |
||
Adjusts the width of the vertical line. |
|||
001 |
600dpi:Bk |
*ENG |
[10 to 15 / 15 / 1 /step] |
002 |
600dpi:Ma |
*ENG |
|
003 |
600dpi:Cy |
*ENG |
|
004 |
600dpi:Ye |
*ENG |
|
005 |
1200dpi:Bk |
*ENG |
|
006 |
1200dpi:Ma |
*ENG |
|
007 |
1200dpi:Cy |
*ENG |
|
008 |
1200dpi:Ye |
*ENG |
2181 |
[Line Position Adj. Result] |
||
Displays the values for each correction.
|
|||
001 |
Paper Int. Mag: Subdot: Bk |
*ENG |
[–32768 to 32767 / 0 / 1 pulse/step] |
002 |
Mag.Cor. Subdot: Bk |
*ENG |
[–32768 to 32767 / 0 / 1 pulse/step] |
003 |
Skew: M |
*ENG |
[–5000 to 5000 / 0 / 0.001 um/step] |
005 |
M. Scan Erro.: Left: M |
*ENG |
[–5000 to 5000 / 0 / 0.001 um/step] |
006 |
M. Scan Erro.: Center: M |
*ENG |
|
007 |
M. Scan Erro.: Right: M |
*ENG |
|
008 |
S. Scan Erro.: Left: M |
*ENG |
|
009 |
S. Scan Erro.: Center: M |
*ENG |
|
010 |
S. Scan Erro.: Right: M |
*ENG |
|
011 |
M. Cor.: Dot: M |
*ENG |
[–512 to 511 / 0 / 1 dot/step] |
012 |
M. Cor.: Subdot: M |
*ENG |
[–15 to 15 / 0 / 1 pulse/step] |
013 |
Paper Int. Mag: Subdot: M |
*ENG |
[–32768 to 32767 / 0 / 1 pulse/step] |
014 |
Mag.Cor. Subdot: M |
*ENG |
|
015 |
M. Left Mag.: Subdot: M |
*ENG |
|
016 |
M. Right Mag.: Subdot: M |
*ENG |
|
017 |
S. Cor.: 600 Line: M |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
018 |
S. Cor.: 600 Sub: M |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
019 |
S. Cor.: 1200 Line: M |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
020 |
S. Cor.: 1200 Sub: M |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
021 |
Skew: C |
*ENG |
[–5000 to 5000 / 0 / 0.001 um/step] |
023 |
M. Scan Erro.: Left: C |
*ENG |
[–5000 to 5000 / 0 / 0.001 um/step] |
024 |
M. Scan Erro.: Center: C |
*ENG |
|
025 |
M. Scan Erro.: Right: C |
*ENG |
|
026 |
S. Scan Erro.: Left: C |
*ENG |
|
027 |
S. Scan Erro.: Center: C |
*ENG |
|
028 |
S. Scan Erro.: Right: C |
*ENG |
|
029 |
M. Cor.: Dot: C |
*ENG |
[–512 to 511 / 0 / 1 dot/step] |
030 |
M. Cor.: Subdot: C |
*ENG |
[–15 to 15 / 0 / 1 pulse/step] |
031 |
Paper Int. Mag: Subdot: C |
*ENG |
[–32768 to 32767 / 0 / 1 pulse/step] |
032 |
Mag.Cor. Subdot: C |
*ENG |
|
033 |
M. Left Mag.: Subdot: C |
*ENG |
|
034 |
M. Right Mag.: Subdot: C |
*ENG |
|
035 |
S. Cor.: 600 Line: C |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
036 |
S. Cor.: 600 Sub: C |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
037 |
S. Cor.: 1200 Line: C |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
038 |
S. Cor.: 1200 Sub: C |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
039 |
Skew: Y |
*ENG |
[–5000 to 5000 / 0 / 0.001 um/step] |
041 |
M. Scan Erro.: Left: Y |
*ENG |
|
042 |
M. Scan Erro.: Center: Y |
*ENG |
|
043 |
M. Scan Erro.: Right: Y |
*ENG |
|
044 |
S. Scan Erro.: Left: Y |
*ENG |
|
045 |
S. Scan Erro.: Center: Y |
*ENG |
|
046 |
S. Scan Erro.: Right: Y |
*ENG |
|
047 |
M. Cor.: Dot: Y |
*ENG |
[–512 to 511 / 0 / 1 dot/step] |
048 |
M. Cor.: Subdot: Y |
*ENG |
[–15 to 15 / 0 / 1 pulse/step] |
049 |
Paper Int. Mag: Subdot: Y |
*ENG |
[–32768 to 32767 / 0 / 1 pulse/step] |
050 |
Mag.Cor. Subdot: Y |
*ENG |
|
051 |
M. Left Mag.: Subdot: Y |
*ENG |
|
052 |
M. Right Mag.: Subdot: Y |
*ENG |
|
053 |
S. Cor.: 600 Line: Y |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
054 |
S. Cor.: 600 Sub: Y |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
055 |
S. Cor.: 1200 Line: Y |
*ENG |
[–16384 to 16383 / 0 / 1 line/step] |
056 |
S. Cor.: 1200 Sub: Y |
*ENG |
[–1 to 1 / 0 / 0.001 line/step] |
2182 |
[Line Position Adj. Offset] (Color) M. Scan: Main scan, S. Scan: Sub-scan |
||
001 |
M Magnification |
*ENG |
Adjusts the line position manually. [-1 to 1 / 0 / 0.001%/step] |
002 |
C Magnification |
*ENG |
|
003 |
Y Magnification |
*ENG |
|
When line shifts are not corrected by the automatic line position adjustment, do this SP. Increasing a value reduces the image in the main scan direction. Decreasing a value enlarges the image in the main scan direction. |
|||
004 |
M. Scan: High: Dot: M |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
005 |
M. Scan: High: Subdot: M |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
006 |
M. Scan: Medium: Dot: M |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
007 |
M. Scan: Medium: Subdot: M |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
008 |
M. Scan: Low: Dot: M |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
009 |
M. Scan: Low: Subdot: M |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
010 |
M. Scan: High: Dot: C |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
011 |
M. Scan: High: Subdot: C |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
012 |
M. Scan: Medium: Dot: C |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
013 |
M. Scan: Medium: Subdot: C |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
014 |
M. Scan: Low: Dot: C |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
015 |
M. Scan: Low: Subdot: C |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
016 |
M. Scan: High: Dot: Y |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
017 |
M. Scan: High: Subdot: Y |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
018 |
M. Scan: Medium: Dot: Y |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
019 |
M. Scan: Medium: Subdot: Y |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
020 |
M. Scan: Low: Dot: Y |
*ENG |
[-512 to 511 / 0 / 1 dot/step] |
021 |
M. Scan: Low: Subdot: Y |
*ENG |
[-15 to 15 / 0 / 1 pulse/step] |
022 |
S. Scan: High: Line: M |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
023 |
S. Scan: High: Subline: M |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
024 |
S. Scan: Medium: Line: M |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
025 |
S. Scan: Medium: Subline: M |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
026 |
S. Scan: Low: Line: M |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
027 |
S. Scan: Low: Subline: M |
*ENG |
Not used |
028 |
S. Scan: High: Line: C |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
029 |
S. Scan: High: Subline: C |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
030 |
S. Scan: Medium: Line: C |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
031 |
S. Scan: Medium: Subline: C |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
032 |
S. Scan: Low: Line: C |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
033 |
S. Scan: Low: Subline: C |
*ENG |
Not used |
034 |
S. Scan: High: Line: Y |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
035 |
S. Scan: High: Subline: Y |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
036 |
S. Scan: Medium: Line: Y |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
037 |
S. Scan: Medium: Subline: Y |
*ENG |
[–1 to 1 / 0 / 0.001 /line] |
038 |
S. Scan: Low: Line: Y |
*ENG |
[-16384 to 16383 / 0 / 1 line/step] |
039 |
S. Scan: Low: Subline: Y |
*ENG |
Not used |
2185 |
[Main Scan Length Detection Disp.] |
||
Displays/adjusts the target value for the main scan magnification correction of the line position adjustment. After replacing the laser optics housing unit, input the standard value for Bk provided with the new unit. For details, see "Laser Optics Housing Unit" in the "Replacement Adjustment" section. It is not necessary to input the values for the other colors; these are automatically adjusted after doing the line position adjustment. |
|||
001 |
Bk |
*ENG |
[0 to 266667 / 249449 / 1 sub-dot/step] |
002 |
M |
*ENG |
|
003 |
C |
*ENG |
|
004 |
Y |
*ENG |
2193 |
[MUSIC Condition Set] Line Position Adjustment: Condition Setting |
||||||
001 |
Auto Execution |
*ENG |
[0 or 1 / 1 / 1 ] 0: OFF, 1: ON |
||||
Enables/disables the automatic line position adjustment |
|||||||
002 |
Page: Job End: BW+FC |
*ENG |
[0 to 999 / 500 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for BW and color printing mode after job end. |
|||||||
003 |
Page: Job End: FC |
*ENG |
[0 to 999 / 200 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for color printing mode after job end. |
|||||||
004 |
Page: Interrupt: BW+FC |
*ENG |
[0 to 999 / 200 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for BW and color printing mode during job. |
|||||||
005 |
Page: Interrupt: FC |
*ENG |
[0 to 999 / 200 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for color printing mode during jobs. |
|||||||
006 |
Page: Stand-By: BW |
*ENG |
[0 to 999 / 100 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for BW printing mode in stand-by mode. The line position adjustment is done when the number of outputs in BW printing mode reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is satisfied. |
|||||||
007 |
Page: Stand-By: FC |
*ENG |
[0 to 999 / 100 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for FC printing mode in stand-by mode. The line position adjustment is done when the number of outputs in color printing mode reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is satisfied. |
|||||||
008 |
Temp. |
*ENG |
[0 to 100 / 5 / 1deg/step] |
||||
Adjust the temperature change threshold for the line position adjustment (Mode b: adjustment once). The timing for line position adjustment depends on the combinations of several conditions. |
|||||||
009 |
Time |
*ENG |
[1 to 1440 / 300 / 1 minute/step] |
||||
Adjust the time threshold for the line position adjustment (Mode b: adjustment once). The timing for line position adjustment depends on the combinations of several conditions. |
|||||||
010 |
Magnification |
*ENG |
[0 to 10 / 0.1 / 0.01%/step] |
||||
Adjusts the magnification threshold for line position adjustment. If the length of the main scan is changed by this amount since the previous MUSIC, then MSUIC is done again. |
|||||||
011 |
Temp. 2 |
*ENG |
[0 to 100 / 10 / 1deg/step] |
||||
Adjust the temperature change threshold for the line position adjustment (Mode a: adjustment twice). The timing for line position adjustment depends on the combinations of several conditions. |
|||||||
012 |
Time 2 |
*ENG |
[1 to 9999 / 600 / 1 minute/step] |
||||
Adjust the time threshold for the line position adjustment (Mode a: adjustment twice). The timing for line position adjustment depends on the combinations of several conditions. |
|||||||
013 |
Page: Power ON:BW+FC |
*ENG |
[0 to 999 / 200 / 1 page/step] |
||||
Adjusts the threshold of the line position adjustment for BW and FC printing mode at power-on. The line position adjustment is done when the number of outputs in BW and color printing mode reaches the value specified with this SP and the condition of SP2-193-008 or SP2-193-009 is satisfied. |
2194 |
[MUSIC Execution Result] Line Position Adjustment: Execution Result |
||
001 |
Year |
*ENG |
[0 to 99 / 0 / 1 year/step] |
Displays the year of the last MUSIC execution. |
|||
002 |
Month |
*ENG |
[1 to 12 / 1 / 1 month/step] |
Displays the month of the last MUSIC execution. |
|||
003 |
Day |
*ENG |
[1 to 31 / 1 / 1 day/step] |
Displays the date of the last MUSIC execution. |
|||
004 |
Hour |
*ENG |
[0 to 23 / 0 / 1 hour/step] |
Displays the time (hour) of the last MUSIC execution. |
|||
005 |
Minute |
*ENG |
[0 to 59 / 0 / 1 minute/step] |
Displays the time (minute) of the last MUSIC execution. |
|||
006 |
Temperature |
*ENG |
[0 to 100 / 0 / 1 deg/step] |
Displays the temperature of the last MUSIC execution. |
|||
007 |
Execution Result |
*ENG |
[0 or 1 / 0 / 1 /step] 0: Completed successfully, 1: Failed |
008 |
Number of Execution |
*ENG |
[0 to 999999 / 0 / 1 times/step] |
009 |
Number of Failure |
*ENG |
[0 to 999999 / 0 / 1 times/step] |
010 |
Error Result: M |
*ENG |
[0 to 9 / 0 / 1 /step] 0: Not done 1: Completed successfully 2: Cannot detect patterns 3: Fewer lines on the pattern than the target 4: Not used 5: Out of the adjustment range 6 to 9: Not used |
011 |
Error Result: C |
*ENG |
|
012 |
Error Result: Y |
*ENG |
2198 |
[Music A/D Interval] |
||
ADC Trigger Counter |
|||
001 |
ADC Trigger Counter |
*ENG |
[7.5 to 20 / 10 / 0.1 |
2220 |
[Skew Origin Set] |
||
Executes the skew motor initialization in the laser optics unit. |
|||
001 |
M: Skew Motor |
- |
- |
002 |
C: Skew Motor |
- |
- |
003 |
Y: Skew Motor |
- |
- |
2221 |
[LD Power] LD Power Control |
||
Adjusts the fixed LD power for each line speed and color. These SPs are activated only when SP3-041-002 is set to "0". Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Plain: Bk |
*ENG |
[0 to 200 / 100 / 1%/step] Increasing this value makes the image density darker. |
002 |
Plain: M |
*ENG |
|
003 |
Plain: C |
*ENG |
|
004 |
Plain: Y |
*ENG |
|
005 |
Thick 1: Bk |
*ENG |
|
006 |
Thick 1: M |
*ENG |
|
007 |
Thick 1: C |
*ENG |
|
008 |
Thick 1: Y |
*ENG |
|
009 |
Thick 2&FINE: Bk |
*ENG |
|
010 |
Thick 2&FINE: M |
*ENG |
|
011 |
Thick 2&FINE: C |
*ENG |
|
012 |
Thick 2&FINE: Y |
*ENG |
2229 |
[Development DC Vias] Development DC Bias Adjustment |
||
Adjusts the development bias. Development bias is automatically adjusted during process control; therefore, adjusting these settings has no effect while Process Control (SP3-041-001 Default: ON) is activated. After deactivating Process Control with SP3-041-001, the values in these SP modes are used for printing. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Plain: Bk |
*ENG |
[0 to 800 / 550 / 10 –V/step] |
002 |
Plain: M |
*ENG |
|
003 |
Plain: C |
*ENG |
|
004 |
Plain: Y |
*ENG |
|
005 |
Thick 1: Bk |
*ENG |
|
006 |
Thick 1: M |
*ENG |
|
007 |
Thick 1: C |
*ENG |
|
008 |
Thick 1: Y |
*ENG |
|
009 |
Thick 2&FINE:Bk |
*ENG |
|
010 |
Thick 2&FINE:M |
*ENG |
|
011 |
Thick 2&FINE:C |
*ENG |
|
012 |
Thick 2&FINE:Y |
*ENG |
2241 |
[Temperature/Humidity: Display] |
||
Displays the environment temperature and humidity. |
|||
001 |
Temperature |
- |
[–1280 to 1270 / - / 0.1deg/step] |
002 |
Relative Humidity |
- |
[0 to 1000 / - / 0.1 %RH/step] |
003 |
Absolute Humidity |
- |
[0 to 100 / - / 0.01 g/m3/step] |
2302 |
[Environmental Correction: Transfer] Environmental Correction: Image Transfer Belt Unit |
||
001 |
Current Environmental Display |
- |
Displays the current environment condition. |
002 |
Forced Setting |
*ENG |
Sets the environment condition manually. [0 to 6 / 0 / 1 /step] 0: Automatic environment control 1: LL (Low temperature/ Low humidity) 2: ML (Middle temperature/ Low humidity) 3: MM (Middle temperature/ Middle humidity) 4: MH (Middle temperature/ High humidity) 5: HH (High temperature/ High humidity) |
003 |
Absolute Humidity: Threshold 1 |
*ENG |
Adjusts the threshold value between LL and ML. [0 to 100 / 4 / 0.01 g/m3/step] |
004 |
Absolute Humidity: Threshold 2 |
*ENG |
Adjusts the threshold value between ML and MM. [0 to 100 / 8 / 0.01 g/m3/step] |
005 |
Absolute Humidity: Threshold 3 |
*ENG |
Adjusts the threshold value between MM and MH. [0 to 100 / 16 / 0.01 g/m3/step] |
006 |
Absolute Humidity: Threshold 4 |
*ENG |
Adjusts the threshold value between MH and HH. [0 to 100 / 24 / 0.01 g/m3/step] |
007 |
Temp Threshold |
*ENG |
[–5 to 30 / 5 / 1 deg/step] |
2308 |
[Paper Size Correction] |
||
Adjusts the threshold value for the paper size correction. |
|||
001 |
Threshold 1 |
*ENG |
[0 to 350 / 297 / 1 mm/step] Threshold 1 ≤ paper: Paper is detected as "S1" size. |
002 |
Threshold 2 |
*ENG |
[0 to 350 / 257 / 1 mm/step] Threshold 2 ≤ paper ≤ Threshold 1: Paper is detected as "S2" size. |
003 |
Threshold 3 |
*ENG |
[0 to 350 / 210 / 1 mm/step] Threshold 3 ≤ paper ≤ Threshold 2: Paper is detected as "S3" size. |
004 |
Threshold 4 |
*ENG |
[0 to 350 / 148 / 1 mm/step] Threshold 4 ≤ paper ≤ Threshold 3: Paper is detected as "S4" size. Paper ≤ Threshold 4: Paper is detected as "S5" size. |
2311 |
[Non Image Area: Bias] |
||
001 |
Image Transfer |
*ENG |
Adjusts the bias of the image transfer belt between images. This value is added to the value of the image transfer belt bias. [10 to 250 / 100 / 5 %/step] |
002 |
Paper Transfer |
*ENG |
Adjusts the bias of the paper transfer roller between images. [0 to 2000 / 500 / 1 V/step] |
2326 |
[Transfer Roller CL: Bias] Transfer Roller Cleaning: Bias Adjustment |
||
001 |
Positive |
*ENG |
[0 to 2100 / 500 / 100 V /step] |
Adjusts the positive voltage of the paper transfer roller for cleaning the paper transfer roller. |
|||
002 |
Negative |
*ENG |
[10 to 400 / 100 / 10 %/step] |
Adjusts the negative current of the paper transfer roller for cleaning the paper transfer roller. |
|||
003 |
Positive |
*ENG |
[0 to 2100 / 2000 / 100 V/step] |
Adjusts the negative current limit of the paper transfer roller for cleaning the paper transfer roller. |
|||
004 |
Negative |
*ENG |
[10 to 400 / 100 / 10 %/step] |
2351 |
[Common: BW: Bias] Image Transfer Belt: B/W: Bias Adjustment Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
||
001 |
ITB unit: Plain |
*ENG |
[0 to 80 / 25 / 1 |
Adjusts the current for the image transfer belt in B/W mode for plain paper. |
|||
002 |
ITB unit: Thick 1 |
*ENG |
[0 to 80 / 12 / 1 |
Adjusts the current for the image transfer belt in B/W mode for thick 1 paper. |
|||
003 |
ITB unit: Thick 2 & FINE |
*ENG |
[0 to 80 / 12 / 1 |
Adjusts the current for the image transfer belt in B/W mode for thick 2 paper or FINE mode. |
2357 |
[Common: FC: Bias] Image Transfer Belt: Full Color: Bias Adjustment Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
ITB unit: Plain: Bk |
*ENG |
[0 to 80 / 22 / 1 |
|
Adjusts the current for the image transfer belt for Black in full color mode for plain paper. |
||||
002 |
ITB unit: Plain: M |
*ENG |
[0 to 80 / 25 / 1 |
|
Adjusts the current for the image transfer belt for Magenta in full color mode for plain paper. |
||||
003 |
ITB unit: Plain: C |
*ENG |
[0 to 80 / 22 / 1 |
|
Adjusts the current for the image transfer belt for Cyan in full color mode for plain paper. |
||||
004 |
ITB unit: Plain: Y |
*ENG |
[0 to 80 / 28 / 1 |
|
Adjusts the current for the image transfer belt for Yellow in full color mode for plain paper. |
||||
005 |
ITB unit: Thick 1: Bk |
*ENG |
[0 to 80 / 11 / 1 |
|
Adjusts the current for the image transfer belt for Black in full color mode for thick 1 paper. |
||||
006 |
ITB unit: Thick 1: M |
*ENG |
[0 to 80 / 12 / 1 |
|
Adjusts the current for the image transfer belt for Magenta in full color mode for thick 1 paper. |
||||
007 |
ITB unit: Thick 1: C |
*ENG |
[0 to 80 / 11 / 1 |
|
Adjusts the current for the image transfer belt for Cyan in full color mode for thick 1 paper. |
||||
008 |
ITB unit: Thick 1: Y |
*ENG |
[0 to 80 / 14 / 1 |
|
Adjusts the current for the image transfer belt for Yellow in full color mode for thick 1 paper. |
||||
009 |
ITB unit: Thick 2 & FINE: Bk |
*ENG |
[0 to 80 / 11 / 1 |
|
Adjusts the current for the image transfer belt for Black in full color mode for Thick 2 and fine. |
||||
010 |
ITB unit: Thick 2 & FINE: M |
*ENG |
[0 to 80 / 12 / 1 |
|
Adjusts the current for the image transfer belt for Magenta in full color mode for Thick 2 and fine. |
||||
011 |
ITB unit: Thick 2 & FINE: C |
*ENG |
[0 to 80 / 11 / 1 |
|
Adjusts the current for the image transfer belt for Cyan in full color mode for Thick 2 and fine. |
||||
012 |
ITB unit: Thick 2 & FINE: Y |
*ENG |
[0 to 80 / 14 / 1 |
|
Adjusts the current for the image transfer belt for Yellow in full color mode for Thick 2 and fine. |
2360 |
[Common: BW Environment Correction] |
||
001 |
ITB unit: Plain |
*ENG |
[1 to 60 / 1 / 1 /step] |
002 |
ITB unit: Thick 1 |
*ENG |
|
003 |
ITB unit: Thick 2 |
*ENG |
|
004 |
ITB unit: Plain: Bk |
*ENG |
[1 to 60 / 13/ 1 /step] |
005 |
ITB unit: Plain: M |
*ENG |
[1 to 60 / 2 / 1 /step] |
006 |
ITB unit: Plain: C |
*ENG |
|
007 |
ITB unit: Plain: Y |
*ENG |
|
008 |
ITB unit: Thick 1: Bk |
*ENG |
[1 to 60 / 31 / 1 /step] |
009 |
ITB unit: Thick 1: M |
*ENG |
[1 to 60 / 2 / 1 /step] |
010 |
ITB unit: Thick 1: C |
*ENG |
|
011 |
ITB unit: Thick 1: Y |
*ENG |
|
012 |
ITB unit: Thick 2: Bk |
*ENG |
[1 to 60 / 31 / 1 /step] |
013 |
ITB unit: Thick 2: M |
*ENG |
[1 to 60 / 2 / 1 /step] |
014 |
ITB unit: Thick 2: C |
*ENG |
[1 to 60 / 1 / 1 /step] |
015 |
ITB unit: Thick 2: Y |
*ENG |
[1 to 60 / 2 / 1 /step] |
2401 |
[Plain: Bias] |
||
Adjusts the DC voltage of the discharge plate for plain paper. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
003 |
Separation DC: 1200: 1st Page |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
004 |
Separation DC: 1200: 2nd side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
2403 |
[Plain: Bias: BW] |
||
Adjusts the current for the paper transfer roller for plain paper in black-and-white mode. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 22 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 7 / 1 – |
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
[0 to 250 / 12 / 1 – |
2407 |
[Plain: Bias: FC] |
||
Adjusts the current for the paper transfer roller for plain paper in full color mode. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 27 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 250 / 33 / 1 – |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 10 / 1 – |
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
[0 to 250 / 12 / 1 – |
2411 |
[Plain: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2403 and SP2407 are multiplied by these SP values. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain : 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: Plain: 2nd Side: S1 |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
|
004 |
Separation DC: 1200: 2nd Side |
*ENG |
|
005 |
Paper Transfer: Plain: 1st Side: S2 |
*ENG |
[100 to 600 / 105 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
006 |
Paper Transfer: Plain: 2nd Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
007 |
Paper Transfer: 1200: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
008 |
Paper Transfer: 1200: 2nd Side: S2 |
*ENG |
[100 to 600 / 150 / 5%/step] |
009 |
Paper Transfer: Plain: 1st Side: S3 |
*ENG |
[100 to 600 / 110 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
010 |
Paper Transfer: Plain: 2nd Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
011 |
Paper Transfer: 1200: 1st Side: S3 |
*ENG |
|
012 |
Paper Transfer: 1200: 2nd Side: S3 |
*ENG |
[100 to 600 / 300 / 5%/step] |
013 |
Paper Transfer: Plain: 1st Side: S4 |
*ENG |
[100 to 600 / 115 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
014 |
Paper Transfer: Plain: 2nd Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
015 |
Paper Transfer: 1200: 1st Side: S4 |
*ENG |
[100 to 600 / 240 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
016 |
Paper Transfer: 1200: 2nd Side: S4 |
*ENG |
[100 to 600 / 340 / 5%/step] |
017 |
Paper Transfer: Plain: 1st Side: S5 |
*ENG |
[100 to 600 / 120 / 5%/step] 148 mm > S5 size (Paper width) |
018 |
Paper Transfer: Plain: 2nd Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
019 |
Paper Transfer: 1200: 1st Side: S5 |
*ENG |
[100 to 600 / 300 / 5%/step] 148 mm > S5 size (Paper width) |
020 |
Paper Transfer: 1200: 2nd Side: S5 |
*ENG |
[100 to 600 / 400 / 5%/step] |
2421 |
[Plain: Leading Edge Correction] Plain Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2403 and SP2407 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
|
2421 005-008 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2401 is multiplied by these SPs values.
|
||
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
|
008 |
Separation DC: 1200: 2nd Side |
*ENG |
2422 |
[Plain: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
|
008 |
Separation DC: 1200: 2nd Side |
*ENG |
2423 |
[Plain: Trailing Edge Correction] Plain Paper: Trailing Edge Correction |
||
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2403 and SP2407 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
|
008 |
Separation DC: 1200: 2nd Side |
*ENG |
2424 |
[Plain: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
004 |
Paper Transfer: 1200: 2nd side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
|
008 |
Separation DC: 1200: 2nd Side |
*ENG |
2451 |
[Thin: Bias] |
||
Adjusts the DC voltage of the discharge plate for thin paper. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 2000 / 10 –V/step] |
003 |
Separation DC: 1200: 1st Side |
*ENG |
2453 |
[Thin: Bias: BW] |
||
Adjusts the current for the paper transfer roller for thin paper in black-and-white mode. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 22 / 1 – |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 11 / 1 – |
2457 |
[Thin: Bias: FC] |
||
Adjusts the current for the paper transfer roller for thin paper in full color mode. Plain: High speed, Thick 1: Middle speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 30 / 1 – |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
2461 |
[Thin: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2453 and SP2457 are multiplied by these SP values. Plain: High speed |
|||
001 |
Paper Transfer: Plain: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
005 |
Paper Transfer: Plain: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
009 |
Paper Transfer: Plain: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
013 |
Paper Transfer: Plain: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 297 mm > S2 size > 275 mm (Pape r width) |
017 |
Paper Transfer: Plain: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] |
2471 |
[Thin: Leading Edge Correction] Thin Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2453 and SP2457 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
2471 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2451 is multiplied by these SP values.
|
||
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
2472 |
[Thin: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed, |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2473 |
[Thin: Trailing Edge Correction] Thin Paper: Trailing Edge Correction |
||
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2453 and SP2457 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
2474 |
[Thin: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 1 mm/step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
2480 |
[Thin: Environment Correction] Plain: High speed, 1200: Low speed |
||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
003 |
Paper Transfer: Plain: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
005 |
Paper Transfer: Plain: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
009 |
Paper Transfer: 1200: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
011 |
Paper Transfer: 1200: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2481 |
[Glossy: Bias] |
||
001 |
Separation DC: 1st Side |
*ENG |
[0 to 4000 / 2000 / 10 –V/step] |
Adjusts the DC voltage of the discharge plate for glossy paper. |
2482 |
[Glossy: Bias: BW] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 12 / 1 – |
Adjusts the current for the paper transfer roller for glossy paper in black-and-white mode. |
2483 |
[Glossy: Bias: FC] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
Adjusts the current for the paper transfer roller for glossy paper in full color mode. |
2484 |
[Glossy: Paper Size Correction] |
||
001 |
Paper Transfer: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] |
005 |
Paper Transfer: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] |
009 |
Paper Transfer: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] |
013 |
Paper Transfer: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] |
017 |
Paper Transfer: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] |
2485 |
[Glossy: Leading Edge Correction] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[10 to 400 / 100 / 5%/step] |
005 |
Separation DC: 1st Side |
*ENG |
[10 to 400 / 100 / 5%/step]] |
2486 |
[Glossy: Switch Timing: Lead. Edge] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
005 |
Separation DC: 1st Side |
*ENG |
2487 |
[Glossy: Trailing Edge Correction] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5 %/step] |
005 |
Separation DC: 1st Side |
*ENG |
2488 |
[Glossy: Switch Trail. Edge] |
||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
005 |
Separation DC: 1st Side |
*ENG |
2489 |
[Glossy: Environment Correction] |
||
001 |
Separation DC: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
003 |
Paper Transfer: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
005 |
Paper Transfer: FC: 2nd Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2501 |
[Thick 1: Bias] |
||
Adjusts the DC voltage of the discharge plate for thick 1 paper. Plain: High speed, 1200: Low speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 1000 / 10 –V/step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
2502 |
[Thick 1: Bias: BW] |
||
Adjusts the current for the paper transfer roller for thick 1 paper in black-and-white mode. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 24 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 250 / 12 / 1 – |
2507 |
[Thick 1: Bias: FC] |
||
Adjusts the current for the paper transfer roller for thick 1 paper in full color mode. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 30 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
2511 |
[Thick 1: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2502 and SP2507 are multiplied by these SP values. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: Plain: 2nd Side: S1 |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
005 |
Paper Transfer: Plain: 1st Side: S2 |
*ENG |
[100 to 600 / 105 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
006 |
Paper Transfer: Plain: 2nd Side: S2 |
*ENG |
[100 to 600 / 130 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
007 |
Paper Transfer: 1200: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
009 |
Paper Transfer: Plain: 1st Side: S3 |
*ENG |
[100 to 600 / 110 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
010 |
Paper Transfer: Plain: 2nd Side: S3 |
*ENG |
[100 to 600 / 160 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
011 |
Paper Transfer: 1200: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
013 |
Paper Transfer: Plain 1: 1st Side: S4 |
*ENG |
[100 to 600 / 115 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
014 |
Paper Transfer: Plain: 2nd Side: S4 |
*ENG |
[100 to 600 / 190 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
015 |
Paper Transfer: 1200: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
017 |
Paper Transfer: Plain 1: 1st Side: S5 |
*ENG |
[100 to 600 / 120 / 5%/step] 148 mm > S5 size (Paper width) |
018 |
Paper Transfer: Plain: 2nd Side: S5 |
*ENG |
[100 to 600 / 220 / 5%/step] 148 mm > S5 size (Paper width) |
019 |
Paper Transfer: 1200: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
2521 |
[Thick 1: Leading Edge Correction] Thick 1 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2502 and SP2507 are multiplied by these SP values. Thick 1: Middle speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
2522 |
[Thick 1: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Thick 1: Middle speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain 1: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain 1: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
006 |
Separation DC: Plain 1: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2523 |
[Thick 1: Trailing Edge Correction] Thick 1 Paper: Trailing Edge Correction |
||
Adjusts the correction coefficient to the paper transfer roller current for the paper trailing edge in each mode. SP2502 and SP2507 are multiplied by these SP values. Thick 1: Middle speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Paper Transfer: Plain: 1st Side |
*ENG |
|
006 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
007 |
Paper Transfer: 1200: 1st Side |
*ENG |
2524 |
[Thick 1: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 1 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Paper Transfer: Plain: 1st Side |
*ENG |
|
006 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
007 |
Paper Transfer: 1200: 1st Side |
*ENG |
2530 |
[Thick 1: Environment Correction] Plain: High speed, 1200: Low speed |
||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[1 to 60 / 22 / 1 /step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: Plain: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
004 |
Paper Transfer: Plain: BW:2nd Side |
*ENG |
|
005 |
Paper Transfer: Plain: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
006 |
Paper Transfer: Plain: FC:2nd Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
[1 to 60 / 22 / 1 /step] |
009 |
Paper Transfer: 1200: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
011 |
Paper Transfer: 1200: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2551 |
[Thick 2: Bias] |
||
Adjusts the DC voltage of the discharge plate for thick 2 paper. |
|||
001 |
Separation DC: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
002 |
Separation DC: 2nd Side |
*ENG |
2553 |
[Thick 2: Bias: BW] |
||
Adjusts the current for the paper transfer roller for thick 2 paper in black-and-white mode. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 7 / 1 – |
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 12 / 1 – |
2558 |
[Thick 2: Bias: FC] |
||
Adjusts the current for the paper transfer roller for thick 2 paper in full color mode. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 16 / 1 – |
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 15 / 1 – |
2561 |
[Thick 2: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2553 and SP2558 are multiplied by these SP values. |
|||
001 |
Paper Transfer: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: 2nd Side: S1 |
*ENG |
|
003 |
Paper Transfer: 1st Side: S2 |
*ENG |
[100 to 600 / 105 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
004 |
Paper Transfer: 2nd Side: S2 |
*ENG |
[100 to 600 / 160 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
005 |
Paper Transfer: 1st Side: S3 |
*ENG |
[100 to 600 / 110 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
006 |
Paper Transfer: 2nd Side: S3 |
*ENG |
[100 to 600 / 260 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
007 |
Paper Transfer: 1st Side: S4 |
*ENG |
[100 to 600 / 120 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
008 |
Paper Transfer: 2nd Side: S4 |
*ENG |
[100 to 600 / 430 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
009 |
Paper Transfer: 1st Side: S5 |
*ENG |
[100 to 600 / 140 / 5%/step] 148 mm > S5 size (Paper width) |
010 |
Paper Transfer: 2nd Side: S5 |
*ENG |
[100 to 600 / 600 / 5%/step] 148 mm > S5 size (Paper width) |
2571 |
[Thick 2: Leading Edge Correction] Thick 2 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2553 and SP2558 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
2571 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2551 is multiplied by these SP values.
|
||
003 |
Separation DC: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
004 |
Separation DC: 2nd Side |
*ENG |
2572 |
[Thick 2: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2mm/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2573 |
[Thick 2: Trailing Edge Correction] Thick 2 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2553 and SP2558 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
004 |
Separation DC: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
2574 |
[Thick 2: Switch Trailing Edge Correction] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2580 |
[Thick 2 Environment Correction] |
||
001 |
Separation DC: 1st Side |
*ENG |
[1 to 60 / 22 / 1 /step] |
002 |
Separation DC: 2nd Side |
*ENG |
|
003 |
Paper Transfer: BW: 1st Side |
*ENG |
[0 to 60 / 11 / 1 /step] |
004 |
Paper Transfer: BW: 2nd Side |
*ENG |
|
005 |
Paper Transfer: FC: 1st Side |
*ENG |
[1 to 60 / 53 / 1 /step] |
006 |
Paper Transfer: FC: 2nd Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
2601 |
[OHP: Bias] |
||
Adjusts the DC voltage of the discharge plate for OHP. |
|||
001 |
Separation DC |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
2603 |
[OHP: Bias: BW] |
||
Adjusts the current for the paper transfer roller for OHP in black-and-white mode. |
|||
001 |
Paper Transfer |
*ENG |
[0 to 250 / 12 / 1 – |
2608 |
[OHP: Bias: FC] |
||
Adjusts the current for the paper transfer roller for OHP in full color mode. |
|||
001 |
Paper Transfer |
*ENG |
[0 to 250 / 15 / 1 – |
2611 |
[OHP: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2603 and SP2608 are multiplied by these SP values. |
|||
001 |
Paper Transfer: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: S2 |
*ENG |
[100 to 600 / 140 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
003 |
Paper Transfer: S3 |
*ENG |
[100 to 600 / 200 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
004 |
Paper Transfer: S4 |
*ENG |
[100 to 600 / 260 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
005 |
Paper Transfer: S5 |
*ENG |
[100 to 600 / 330 / 5%/step] 148 mm > S5 size (Paper width) |
2621 |
[OHP: Leadin Edge Correction] OHP: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2603 and SP2608 are multiplied by these SP values.
|
|||
001 |
Paper Transfer |
*ENG |
[0 to 400 / 100 / 5%/step] |
2621 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2601 is multiplied by these SP values.
|
||
002 |
Separation DC |
*ENG |
[0 to 400 / 100 / 5%/step] |
2622 |
[OHP: Switch Timing: Leadn. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Separation DC |
*ENG |
2623 |
[OHP: Trailing Edge Correction] OHP: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2603 and SP2608 are multiplied by these SP values.
|
|||
001 |
Paper Transfer |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Separation DC |
*ENG |
2624 |
[OHP: Trailing Edge Correction] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer |
*ENG |
[–100 to 0 / 0 / 1 mm/step] |
002 |
Separation DC |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
2630 |
[OHP: Environment Correction] |
||
001 |
Separation DC |
*ENG |
[1 to 60 / 22 / 1 /step] |
002 |
Paper Transfer: BW |
*ENG |
[1 to 60 / 11 / 1 /step] |
003 |
Paper Transfer: FC |
*ENG |
[1 to 60 / 1 / 1 /step] |
2650 |
[Thick3: Bias] |
||
Adjusts the DC voltage of the discharge plate for thick paper 3. |
|||
001 |
Separation DC: 1st Side |
*ENG |
[0 to 4000 / 1000 / 10 –V/step] |
002 |
Separation DC: 2nd Side |
*ENG |
2651 |
[Thick3: Bias: BW] |
||
Adjusts the current for the paper transfer roller for thick paper 3 in black-and-white mode. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 10 / 1 – |
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 12 / 1 – |
2652 |
[Thick3: Bias: FC] |
||||
Adjusts the current for the paper transfer roller for thick paper 3 in full color mode. |
|||||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 11 / 1 – |
||
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 15 / 1 – |
||
2653 |
[Thick3: Paper Size Correction] |
||||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2651 and SP2652 are multiplied by these SP values. |
|||||
001 |
Paper Transfer: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
||
002 |
Paper Transfer: 1st Side: S2 |
*ENG |
[100 to 600 / 100 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
||
003 |
Paper Transfer: 1st Side: S3 |
*ENG |
[100 to 600 / 100 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
||
004 |
Paper Transfer: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
||
005 |
Paper Transfer: 1st Side: S5 |
*ENG |
[100 to 600 / 100 / 5%/step] 148 mm > S5 size (Paper width) |
||
006 |
Paper Transfer: 2nd Side: S1 |
*ENG |
[100 to 600 / 260 / 5%/step] S1 size > 297 mm (Paper width) |
||
007 |
Paper Transfer: 2nd Side: S2 |
*ENG |
[100 to 600 / 100 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
||
008 |
Paper Transfer: 2nd Side: S3 |
*ENG |
[100 to 600 / 430 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
||
009 |
Paper Transfer: 2nd Side: S4 |
*ENG |
[100 to 600 / 100 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
||
010 |
Paper Transfer: 2nd Side: S3 |
*ENG |
[100 to 600 / 600 / 5%/step] 148 mm > S5 size (Paper width) |
2654 |
[Thick 3: Leading Edge Correction] Thick 3 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2651 and SP2652 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Separation DC: 1st Side |
*ENG |
|
2654 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2650 is multiplied by these SP values.
|
||
003 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
004 |
Separation DC: 2nd Side |
*ENG |
2655 |
[Thick 3: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Separation DC: 1st Side |
*ENG |
|
003 |
Paper Transfer: 2nd Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2656 |
[Thick 3: Trailing Edge Correction] Thick 3 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2651 and SP2652 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2657 |
[Thick 3: Trailing Edge Correction] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2660 |
[Thick 3: Environment Correction] Thick 3 Paper: MM Environment Coefficient Adjustment |
||||
Adjusts the environment coefficient for each mode. When the environment is detected as MM, SP2651 and SP2652 are multiplied by these SP values. |
|||||
001 |
Separation DC: 1st Side |
*ENG |
[1 to 60 / 22 / 1 /step] |
||
002 |
Separation DC: 2nd Side |
*ENG |
|||
Adjusts the environment coefficient for each mode. When the environment is detected as MM, SP2650 is multiplied by these SP values. |
|||||
003 |
Paper Transfer: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
||
004 |
Paper Transfer: BW: 2nd Side |
*ENG |
|||
005 |
Paper Transfer: FC: 1st Side |
*ENG |
[1 to 60 / 55 / 1 /step] |
||
006 |
Paper Transfer: FC: 2st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
2670 |
[Thick4: Bias] |
||
Adjusts the DC voltage of the discharge plate for thick paper 4. |
|||
001 |
Separation DC: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
002 |
Separation DC: 2nd Side |
*ENG |
2671 |
[Thick4: Bias: BW] |
||
Adjusts the current for the paper transfer roller for thick paper 4 in black-and-white mode. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 10 / 1 – |
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 11 / 1 – |
2672 |
[Thick4: Bias: FC] |
||
Adjusts the current for the paper transfer roller for thick paper 4 in full color mode. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 250 / 11 / 1 – |
002 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 250 / 15 / 1 – |
2673 |
[Thick4: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2671 and SP2672 are multiplied by these SP values. |
|||
001 |
Paper Transfer: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: 1st Side: S2 |
*ENG |
[100 to 600 / 100 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
003 |
Paper Transfer: 1st Side: S3 |
*ENG |
[100 to 600 / 100 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
004 |
Paper Transfer: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
005 |
Paper Transfer: 1st Side: S5 |
*ENG |
[100 to 600 / 100 / 5%/step] 148 mm > S5 size (Paper width) |
006 |
Paper Transfer: 2nd Side: S1 |
*ENG |
[100 to 600 / 260 / 5%/step] S1 size > 297 mm (Paper width) |
007 |
Paper Transfer: 2nd Side: S2 |
*ENG |
[100 to 600 / 100 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
008 |
Paper Transfer: 2nd Side: S3 |
*ENG |
[100 to 600 / 430 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
009 |
Paper Transfer: 2nd Side: S4 |
*ENG |
[100 to 600 / 100 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
010 |
Paper Transfer: 2nd Side: S3 |
*ENG |
[100 to 600 / 600 / 5%/step] 148 mm > S5 size (Paper width) |
2674 |
[Thick 4: Leading Edge Correction] Thick 4 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2671 and SP2672 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Separation DC: 1st Side |
*ENG |
|
2674 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2670 is multiplied by these SP values.
|
||
003 |
Paper Transfer: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
004 |
Separation DC: 2nd Side |
*ENG |
2675 |
[Thick 4: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Separation DC: 1st Side |
*ENG |
|
003 |
Paper Transfer: 2nd Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2676 |
[Thick 4: Trailing Edge Correction] Thick 4 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2671 and SP2672 are multiplied by these SP values.
|
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2677 |
[Thick 4: Trailing Edge Correction] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. |
|||
001 |
Paper Transfer: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: 2nd Side |
*ENG |
|
003 |
Separation DC: 1st Side |
*ENG |
|
004 |
Separation DC: 2nd Side |
*ENG |
2680 |
[Thick 4: Environment Correction] Thick 4 Paper: MM Environment Coefficient Adjustment |
||||
Adjusts the environment coefficient for each mode. When the environment is detected as MM, SP2671 and SP2672 are multiplied by these SP values. |
|||||
001 |
Separation DC: 1st Side |
*ENG |
[1 to 60 / 22 / 1 /step] |
||
002 |
Separation DC: 2nd Side |
*ENG |
|||
Adjusts the environment coefficient for each mode. When the environment is detected as MM, SP2670 is multiplied by these SP values. |
|||||
003 |
Paper Transfer: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
||
004 |
Paper Transfer: BW: 2nd Side: |
*ENG |
|||
005 |
Paper Transfer: FC: 1st Side |
*ENG |
[1 to 60 / 55 / 1 /step] |
||
006 |
Paper Transfer: FC: 2st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
2751 |
[Special1: Bias] |
||
Adjusts the DC voltage of the discharge plate for special paper 1. Plain: High speed, Thick 1: Middle speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: Thick 1: 1st Side |
*ENG |
2753 |
[Special1: Bias: BW] |
||
Adjusts the current for the paper transfer roller for special paper 1 in black-and-white mode. P Plain: High speed, Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 22 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 11 / 1 – |
2757 |
[Special1: Bias: FC] |
||
Adjusts the current for the paper transfer roller for special paper 1 in full color mode. Plain: High speed, Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 30 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 250 / 33 / 1 – |
003 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
2761 |
[Special1: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2753 and SP2757 are multiplied by these SP values. Plain: High speed, Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: Plain: 2nd Side: S1 |
*ENG |
|
005 |
Paper Transfer: Plain: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
006 |
Paper Transfer: Plain: 2nd Side: S2 |
*ENG |
|
009 |
Paper Transfer: Plain: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
010 |
Paper Transfer: Plain: 2nd Side: S3 |
*ENG |
|
013 |
Paper Transfer: Plain: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
014 |
Paper Transfer: Plain: 2nd Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
017 |
Paper Transfer: Plain: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
018 |
Paper Transfer: Plain: 2nd Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
2771 |
[Special 1: Leading Edge Correction] Special 1 Paper: Leading Edge Correction |
||||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2753 and SP2757 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
||
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
||
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
||
2771 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2751 is multiplied by these SP values.
|
||||
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
||
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|||
007 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
2772 |
[Special 1: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 50 / 0 / 1 mm/step] |
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2773 |
[Special 1: Trailing Edge Correction] Special 1 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2753 and SP2757 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2774 |
[Special 1: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2780 |
[Special 1: Environment Correction] Plain: High speed, 1200: Low speed |
||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
[1 to 60 / 32 / 1 /step] |
003 |
Paper Transfer: Plain: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
004 |
Paper Transfer: Plain: BW:2nd Side |
*ENG |
|
005 |
Paper Transfer: Plain: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
006 |
Paper Transfer: Plain: FC:2nd Side |
*ENG |
[1 to 60 / 14 / 1 /step] |
007 |
Separation DC: 1200: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
009 |
Paper Transfer: 1200: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
011 |
Paper Transfer: 1200: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2801 |
[Special2: Bias] |
||
Adjusts the DC voltage of the discharge plate for special paper 2. Plain: High speed, 1200: Low speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
2803 |
[Special2: Bias: BW] |
||
Adjusts the current for the paper transfer roller for special paper 2 in black-and-white mode. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 22 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 200 / 11 / 1 – |
2807 |
[Special2: Bias: FC] |
||
Adjusts the current for the paper transfer roller for special paper 2 in full color mode. Plain: High speed, Thick 2&Fine: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 30 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 250 / 33 / 1 – |
003 |
Separation DC: 1200: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
2811 |
[Special2: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2803 and SP2807 are multiplied by these SP values. |
|||
001 |
Paper Transfer: Plain: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: Plain: 2nd Side: S1 |
*ENG |
|
005 |
Paper Transfer: Plain: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
006 |
Paper Transfer: Plain: 2nd Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
009 |
Paper Transfer: Plain: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
010 |
Paper Transfer: Plain: 2nd Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
013 |
Paper Transfer: Plain: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
014 |
Paper Transfer: Plain: 2nd Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
017 |
Paper Transfer: Plain: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
018 |
Paper Transfer: Plain: 2nd Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
2821 |
[Special 2: Leading Edge Correction] Special 2 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2803 and SP2807 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
2821 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2801 is multiplied by these SP values.
|
||
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 12001st Side |
*ENG |
2822 |
[Special 2: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2823 |
[Special 2: Trailing Edge Correction] Special 2 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2803 and SP2807 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2824 |
[Special 2: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2830 |
[Special 2: Environment Correction] Plain: High speed, 1200: Low speed |
||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[1 to 60 / 32 / 1 /step] |
003 |
Paper Transfer: Plain: BW: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
004 |
Paper Transfer: Plain: BW:2nd Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
005 |
Paper Transfer: Plain: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
006 |
Paper Transfer: Plain: FC:2nd Side |
*ENG |
[1 to 60 / 14 / 1 /step] |
007 |
Paper Transfer: 1200: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
009 |
Paper Transfer: 1200: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
011 |
Paper Transfer: 1200: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2851 |
[Special 3: Bias] |
||
Adjusts the DC voltage of the discharge plate for special paper 3. Plain: High speed, 1200: Low speed |
|||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 4000 / 0 / 10 –V/step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
|
003 |
Separation DC: 1200: 1st Side |
*ENG |
2852 |
[Special 3: Bias: BW] |
||
Adjusts the current for the paper transfer roller for special paper 3 in black-and-white mode. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 22 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 11 / 1 – |
2857 |
[Special 3: Bias: FC] |
||
Adjusts the current for the paper transfer roller for special paper 3 in full color mode. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 250 / 30 / 1 – |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
[0 to 250 / 33 / 1 – |
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
[0 to 250 / 15 / 1 – |
2861 |
[Special 3: Paper Size Correction] |
||
Adjusts the size correction coefficient for the paper transfer roller current for each paper size. SP2852 and SP2857 are multiplied by these SP values. Thick 1: Middle speed |
|||
001 |
Paper Transfer: Thick 1: 1st Side: S1 |
*ENG |
[100 to 600 / 100 / 5%/step] S1 size > 297 mm (Paper width) |
002 |
Paper Transfer: Thick 1: 2nd Side: S1 |
*ENG |
|
005 |
Paper Transfer: Thick 1: 1st Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
006 |
Paper Transfer: Thick 1: 2nd Side: S2 |
*ENG |
[100 to 600 / 120 / 5%/step] 297 mm > S2 size > 275 mm (Paper width) |
009 |
Paper Transfer: Thick 1: 1st Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
010 |
Paper Transfer: Thick 1: 2nd Side: S3 |
*ENG |
[100 to 600 / 140 / 5%/step] 275 mm > S3 size > 210 mm (Paper width) |
013 |
Paper Transfer: Thick 1: 1st Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
014 |
Paper Transfer: Thick 1: 2nd Side: S4 |
*ENG |
[100 to 600 / 160 / 5%/step] 210 mm > S4 size > 148 mm (Paper width) |
017 |
Paper Transfer: Thick 1: 1st Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
018 |
Paper Transfer: Thick 1: 2nd Side: S5 |
*ENG |
[100 to 600 / 180 / 5%/step] 148 mm > S5 size (Paper width) |
2871 |
[Special 3: Leading Edge Correction] Special 3 Paper: Leading Edge Correction |
||
Adjusts the correction to the paper transfer roller current at the paper leading edge in each mode. SP2852 and SP2857 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
2871 |
Adjusts the correction to the discharge plate current at the paper leading edge in each mode. SP2851 is multiplied by these SP values.
|
||
005 |
Separation DC: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
2872 |
[Special 3: Switch Timing: Lead. Edge] |
||
Adjusts the bias/ voltage switch timing of the paper transfer roller/ discharge plate at the paper leading edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Page |
*ENG |
2873 |
[Special 3: Trailing Edge Correction] Special 3 Paper: Trailing Edge Correction |
||
Adjusts the correction to the paper transfer roller current for the paper trailing edge in each mode. SP2852 and SP2857 are multiplied by these SP values. Plain: High speed, 1200: Low speed
|
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 400 / 100 / 5%/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Page |
*ENG |
2874 |
[Special 3: Switch Timing: Trail. Edge] |
||
Adjusts the bias/voltage switch timing of the paper transfer roller/discharge plate at the paper trailing edge between the erase margin area and the image area. Plain: High speed, 1200: Low speed |
|||
001 |
Paper Transfer: Plain: 1st Side |
*ENG |
[0 to 50 / 0 / 2 mm/step] |
002 |
Paper Transfer: Plain: 2nd Side |
*ENG |
|
003 |
Paper Transfer: 1200: 1st Side |
*ENG |
|
005 |
Separation DC: Plain: 1st Side |
*ENG |
|
006 |
Separation DC: Plain: 2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Page |
*ENG |
2880 |
[Special 3: Environment Correction] Plain: High speed, 1200: Low speed |
||
001 |
Separation DC: Plain: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
002 |
Separation DC: Plain: 2nd Side |
*ENG |
[1 to 60 / 32 / 1 /step] |
003 |
Paper Transfer: Plain: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
004 |
Paper Transfer: Plain: BW:2nd Side |
*ENG |
|
005 |
Paper Transfer: Plain: FC: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
006 |
Paper Transfer: Plain: FC:2nd Side |
*ENG |
|
007 |
Separation DC: 1200: 1st Side |
*ENG |
[1 to 60 / 26 / 1 /step] |
009 |
Paper Transfer: 1200: BW: 1st Side |
*ENG |
[1 to 60 / 11 / 1 /step] |
011 |
Paper Transfer: 1200: FC: 1st Side |
*ENG |
[1 to 60 / 1 / 1 /step] |
2905 |
[Dev Rvs Time] Development Roller Reverse Time |
||
Specified the time of the development roller reverse rotation after the development unit has stopped. The reverse rotation of the development roller is used for removing dust from the development roller. |
|||
001 |
K |
*ENG |
[0 to 200 / 80 / 10 msec/step] |
002 |
M |
*ENG |
|
003 |
C |
*ENG |
|
004 |
Y |
*ENG |
|
005 |
[Dev Rvs Threshold Counter] |
||
All |
*ENG |
[0 to 400000 / 4000/ 10 mm/step] |
|
Specified the threshold distance for the development roller reverse mode. This sp refers to the counters for SP2905-006 to -009. |
|||
[Dev Rvs Counter] |
|||
006 |
K |
*ENG |
[0 to 999999999 / - / 1 mm/step] |
007 |
M |
*ENG |
|
008 |
C |
*ENG |
|
009 |
Y |
*ENG |
2907 |
[ACS Setting (FC to Bk)] |
||
Adjusts the threshold for moving away the image transfer belt from the color PCDUs. This SP moves the image transfer belt away from the color PCDUs when the number of B/W image printouts reaches the number of sheets specified with this SP after consecutive full color image printouts in the full color mode. If this SP is set to "0", the image transfer belt does not move away. |
|||
001 |
Continuous Bk Pages |
*ENG |
[0 to 10 / 0 / 1 sheet/step] |
2920 |
[Transfer Motor Control] |
||
001 |
0: Encorder 1 :FG |
*ENG |
[0 or 1 / 0 / 1 /step] |
Selects the speed control mode for the ITB. If SC443 occurs and machine does not recover, change this setting to "1". |
|||
002 |
SC443 Count |
*ENG |
[0 to 3 / 0 / 1 /step] |
Displays the number of the ITB encodre error. SC443 is displayed if this counter counts to "3". |
2930 |
[SecondaryFB: Threshold] Paper Transfer Roller Feed-back: Threshold Adjustment |
||
Adjusts the threshold between high resistance (division 1) and low resistance (division 2) at the paper transfer roller. This SP affects SP2931 to SP2939. |
|||
001 |
Voltage |
*ENG |
[0 to 7000 / 6000 / 10 –V/step] |
2960 |
[Process Interval] |
||
001 |
Additional Time |
*ENG |
[0 to 10 / 0 / 1 sec/step] |
Adjusts the additional time for ending the machine's process. |
2970 |
[Cleaning After JOB] |
||
001 |
No Refresh |
*ENG |
[0 to 100 / 50 / 1 /step] 0: No cleaning |
Specifies the threshold sheets for the cleaning of the paper transfer roller without the refresh mode. |
|||
002 |
Refresh |
*ENG |
[0 or 1 / 1 / 1 /step] 0: No cleaning, 1: Cleaning |
2971 |
T1 Non Image Area ON Timing |
||
001 |
Standard Speed |
*ENG |
[–400 to 290 / 0 / 10 msec/step] |
Adjusts the timing for the non-image area bias of the image transfer roller. |
|||
002 |
Medium Speed |
*ENG |
[–790 to 410 / 0 / 10 msec/step] |
003 |
Low Speed |
*ENG |
[–790 to 410 / 0 / 10 msec/step] |
2972 |
B/W Image Request Timing |
||
001 |
Standard Speed |
*ENG |
[0 to 4000 / 0 / 10 msec/step] |
002 |
Medium Speed |
*ENG |
[0 to 4000 / 0 / 10 msec/step] |
003 |
Low Speed |
*ENG |
[0 to 4000 / 0 / 10 msec/step] |
2973 |
Forced Process Down Threshold |
||
001 |
- |
*ENG |
[0 to 5000 / 0 / 10 page/step] |
2974 |
OPC PreCharge Time Control |
||
001 |
Standard Speed |
*ENG |
[0 to 940 / 0 / 10 msec/step] |
002 |
Medium Speed |
*ENG |
[0 to 940 / 0 / 10 msec/step] |
003 |
Low Speed |
*ENG |
[0 to 940 / 0 / 10 msec/step] |
2980 |
- |
||
001 |
Continuous Job Page |
*ENG |
[0 to 300 / 100 / 10 page/step] |
002 |
OPC Drum Idling Time BW |
*ENG |
[0 to 600 / 30 / 10 sec/step] |
003 |
OPC Drum Idling Time FC |
*ENG |
[0 to 600 / 30 / 10 sec/step] |
2990 |
Print Duty Control |
||
001 |
Duty Control State |
*ENG |
[0 or 1 / 0 / 1 /step] 0: No limit, 1: Limit |
002 |
Duty Control Thresh Time |
*ENG |
[0 to 195 / 30 / 10 min./step] |
003 |
Duty Control Thresh |
*ENG |
[0 to 999999999 / 0 / 1 mm/step] |
004 |
Forced CPM Down Thresh: No Duty Control |
*ENG |
[0 to 5000 / 0 / 1 page/step] |
005 |
Drum Stop Time: No Duty Control |
*ENG |
[300 to 1500 / 500 / 10 msec/step] |
006 |
ITB Stop Time: No Duty Control |
*ENG |
[300 to 1500 / 500 / 10 msec/step] |
007 |
Forced CPM Down Thresh: Duty Control |
*ENG |
[0 to 5000 / 1 / 1 page/step] |
008 |
Drum Stop Time: Duty Control |
*ENG |
[300 to 1500 / 1500 / 10 msec/step] |
009 |
ITB Stop Time: Duty Control |
*ENG |
[300 to 1500 / 1500 / 10 msec/step] |
010 |
Duty Control: Start Time |
*ENG |
Displays the time of the duty control execution. |