4008 |
[Sub Scan Magnification Adjustment] |
||
Adjusts the sub-scan magnification by changing the scanner motor speed. |
|||
001 |
*ENG |
[-1.0 to 1.0 / 0 / 0.1%/step] FA |
4010 |
[L-Edge Regist Adjustment] |
||
Adjusts the leading edge registration by changing the scanning start timing in the sub-scan direction. |
|||
001 |
- |
*ENG |
[-2.0 to 2.0 / 0 / 0.1 mm/step] FA |
4011 |
[S-to-S Regist Adjustment] |
||
Adjusts the side-to-side registration by changing the scanning start timing in the main scan direction. |
|||
001 |
- |
*ENG |
[-2.5 to 2.5 / 0 / 0.1 mm/step ] FA |
4012 |
[Scanner Erase Margin: Scale] Scanner: Erase Margin: Scale |
||
Sets the blank margin at each side for erasing the original shadow caused by the gap between the original and the scale. |
|||
001 |
Book: Leading Edge |
*ENG |
[0 to 3.0 / 0 / 0.1 mm/step ] FA |
002 |
Book: Trailing Edge |
||
003 |
Book: Left |
||
004 |
Book: Right |
||
005 |
ADF: Leading Edge |
*ENG |
[0 to 3.0 / 0 / 0.1 mm/step ] FA |
007 |
ADF: Right |
||
008 |
ADF: Left |
4013 |
[Scanner Free Run] |
||
Performs the scanner free run with the exposure lamp on or off in the following mode. Full color mode / Full Size / A3 or DLT |
|||
001 |
Lamp: OFF |
*ENG |
[0 or 1 / 0 / - ] 0: OFF, 1: ON |
002 |
Lamp: ON |
4014 |
[Scan] |
||
Execute the scanner free fun with each mode. |
|||
001 |
HP Detection Enable |
- |
Scanner free run with HP sensor check. |
002 |
HP Detection Disable |
- |
Scanner free run without HP sensor check. |
4020 |
[Dust Check] |
||
001 |
Detection: ON/OFF |
*ENG |
Turns the ADF scan glass dust check on/ off. [0 or 1 / 0 / 1 /step] 0: OFF, 1: ON |
002 |
Detection: Level |
*ENG |
Selects the detect level. [0 to 8 / 4 / 1 /step] 0: lowest detection level 8: highest detection level |
003 |
Correction Level |
*ENG |
Selects the level of the sub scan line correction when using the ARDF. [0 to 4 / 0 / 1 /step] 0: Off 1: Weakest 2: Weak 3: Strong 4: Strongest |
011 |
Dust Detect:On/Off:Rear |
*ENG |
Not used |
012 |
Dust Detect:Lvl:Rear |
*ENG |
Not used |
4301 |
[APS Operation Check] |
||
Displays a code that represents the original size detected by the original sensors. (See "Input Check Table" in this section.) |
|||
001 |
APS Operation Check |
- |
- |
4303 |
[APS Min Size (A5/HLT/16K)] |
||
Specifies the result of the detection when the outputs from the original sensors are all OFF. |
|||
001 |
APS Min. Size (A5/HLT/16K) |
*ENG |
[0 to 2 / 0 / 1 /step] 0: No Original 1: A5-Lengthwise (16K SEF if 4305 is set to 3) 2: A5-Sideways (16K LEF if 4305 is set to 3) |
4305 |
[8K/16K Detection] |
*ENG |
[0 to 3 / 0 / 1 /step] 0: Normal Detection (the machine detects A4/LT size as A4 or LT, depending on the paper size setting) 1: A4-Sideways LT-Lengthwise 2: LT-Sideways A4-Lengthwise 3: 8K 16K |
001 |
This program enables the machine to automatically recognize the 8K/16K size. |
4308 |
[Scan Size Detection] |
||
001 |
Detection ON/OFF |
*ENG |
[0 or 1 / 1 / -] 0: OFF 1: ON |
Turns on or off the CCD original size detection. This detection is used only when an original is scanned in book scanning mode. |
4309 |
[Scan Size Detect:Setting] |
||
001 |
Original Density Thresh |
*ENG |
[0 to 255 / 32 / 1 digit/step] |
Specifies the threshold between an original area and non-original area for the scan original size detection in book scanning mode. |
|||
002 |
Detection Time |
*ENG |
[20 to 100 / 60 / 20 msec/step] |
Specifies the detection time for the scan original size detection in book scanning mode. |
|||
003 |
Lamp ON:Delay Time |
*ENG |
[0 to 200 / 40 / 20 msec/step] |
Specifies the lamp on timing for the scan original size detection in book scanning mode. |
4310 |
[Scan Size Detect Value] |
||
Displays the detected value by CCD. Each detection point for paper size and color is displayed on the LCD. |
|||
001 |
S1:R |
*ENG |
[0 to 255 / - / 1 digit/step] |
002 |
S1:G |
*ENG |
|
003 |
S1:B |
*ENG |
|
004 |
S2:R |
*ENG |
|
005 |
S2:G |
*ENG |
|
006 |
S2:B |
*ENG |
|
007 |
S3:R |
*ENG |
|
008 |
S3:G |
*ENG |
|
009 |
S3:B |
*ENG |
4400 |
[Scanner Erase Margin] |
*ENG |
|
Set the Mask for Original. These SPs set the area to be masked during platen (book) mode scanning. |
|||
001 |
Book: Leading Edge |
[0 to 3.0 / 0 / 0.1 mm/step] |
|
002 |
Book: Trailing Edge |
||
003 |
Book: Left |
||
004 |
Book: Right |
||
005 |
ADF: Leading Edge |
||
007 |
ADF: Right |
||
008 |
ADF: Left |
4417 |
[IPU Test Pattern] |
|
Selects the IPU test pattern. |
||
001 |
Test Pattern Selection |
[0 to 24 / 0 / 1/step ] |
0: Scanned image 1: Gradation main scan A 2: Gradation main scan B 3: Gradation main scan C 4: Gradation main scan D 5: Gradation sub scan (1) 6: Grid pattern 7: Slant grid pattern 8: Gradation RGBCMYK 9: UCR pattern 10: Color patch 16 (1) 11: Color patch 16 (2) 12: Color patch 64 |
13: Grid pattern CMYK 14: Color patch CMYK 15: Gray pattern (1) 16: Gray pattern (2) 17: Gray Pattern (3) 18: Shading pattern 19: Thin line pattern 20: Scanned + Grid pattern 21: Scanned + Gray scale 22: Scanned + Color patch 23: Scanned + Slant Grid C 24: Scanned + Slant Grid D |
4429 |
[Illegal Copy Output] |
||
001 |
Copy |
*ENG |
[0 to 3 / 3 / 1 /step] |
002 |
Scanner |
||
003 |
Fax |
4450 |
[Scan Image Path Selection] |
|
001 |
Black Subtraction ON/OFF |
[0 or 1 / 1 / - ] 0: OFF, 1: ON |
Uses or does not use the black reduction image path. |
||
002 |
SH ON/OFF |
[0 or 1 / 0 / 1 /step] 0: ON, 1: OFF |
Uses or does not use the shading image path. |
4501 |
[ACC Target Density] |
||
Selects the ACC result. |
|||
001 |
Copy: K: Text |
*ENG |
[0 to 10 / 5 / 1 /step] 10: Darkest density |
002 |
Copy: C: Text |
*ENG |
|
003 |
Copy: M: Text |
*ENG |
|
004 |
Copy: Y: Text |
*ENG |
|
005 |
Copy: K: Photo |
*ENG |
|
006 |
Copy: C: Photo |
*ENG |
|
007 |
Copy: M: Photo |
*ENG |
|
008 |
Copy: Y: Photo |
*ENG |
4505 |
[ACC Cor:Bright] |
||
Adjusts the offset correction for light areas of the ACC pattern. |
|||
001 |
Text:K |
*ENG |
[-128 to 127 / 0 / 1 /step] |
002 |
Text:C |
*ENG |
|
003 |
Text:M |
*ENG |
|
004 |
Text:Y |
*ENG |
|
005 |
Photo:K |
*ENG |
[-128 to 127 / 0 / 1 /step] |
006 |
Photo:C |
*ENG |
|
007 |
Photo:M |
*ENG |
|
008 |
Photo:Y |
*ENG |
4506 |
[ACC Cor:Dark] |
||
Adjusts the offset correction for dark areas of the ACC pattern. |
|||
001 |
Text:K |
*ENG |
[-128 to 127 / 0 / 1 /step] |
002 |
Text:C |
*ENG |
|
003 |
Text:M |
*ENG |
|
004 |
Text:Y |
*ENG |
|
005 |
Photo:K |
*ENG |
[-128 to 127 / 0 / 1 /step] |
006 |
Photo:C |
*ENG |
|
007 |
Photo:M |
*ENG |
|
008 |
Photo:Y |
*ENG |
4540 |
[Printer Vector Correction] |
||
This SP corrects the printer coverage of 12 hues (RY, YR, YG, etc. x 4 Colors [R, G, B, Option]) for a total of 48 parameters. |
|||
001-004 |
RY Phase: Option/R/G/B |
*ENG |
Specifies the printer vector correction value. [0 to 255 / 0 / 1 /step] |
005-008 |
YR Phase: Option/R/G/B |
||
009-012 |
YG Phase: Option/R/G/B |
||
013-016 |
GY Phase: Option/R/G/B |
||
017-020 |
GC Phase: Option/R/G/B |
||
021-024 |
CG Phase: Option/R/G/B |
||
025-028 |
CB Phase: Option/R/G/B |
||
029-032 |
BC Phase: Option/R/G/B |
||
033-036 |
BM Phase: Option/R/G/B |
||
037-040 |
MB Phase: Option/R/G/B |
||
041-044 |
MR Phase: Option/R/G/B |
||
045-048 |
RM Phase: Option/R/G/B |
4600 |
[SBU Version Display] |
||
001 |
SBU_ID |
- |
Displays the ID of the SBU. |
002 |
GASBU-N_ID |
- |
Displays the ID of the GASBU. |
003 |
VSP5100_ID |
- |
Displays t he ID of the VSP5100. |
4602 |
[Scanner Memory Access] |
||
001 |
Scanner Memory Access |
- |
Enables the read and write check for the SBU registers. |
002 |
Address Set |
- |
Not used |
003 |
Data Set |
- |
4603 |
[AGC Execution] |
||
001 |
HP Detection Enable |
- |
Executes the AGC. |
002 |
HP Detection Disable |
- |
DFU |
4609 |
[Gray Balance Set: R] |
||
001 |
Book Read |
- |
[-512 to 511 / -46 / 1 digit/step] |
002 |
DF Read |
- |
[-512 to 511 / -46 / 1 digit/step] |
4610 |
[Gray Balance Set: G] |
||
001 |
Book Read |
- |
[-512 to 511 / -20 / 1 digit/step] |
002 |
DF Read |
4611 |
[Gray Balance Set: B] |
||
001 |
Book Read |
- |
[-512 to 511 / -28 / 1 digit/step] |
002 |
DF Read |
4623 |
[Black Level Fine Adj. Display] RE: Red Even signal, RO: Red Odd signal |
||
001 |
Latest: RE Color |
- |
Displays the black offset value (rough adjustment) for the even red signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Latest: RO Color |
- |
Displays the black offset value (rough adjustment) for the odd red signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4624 |
[Black Level Rough Adj. Display] GE: Green Even signal, GO: Green Odd signal |
||
001 |
Latest: GE Color |
- |
Displays the black offset value (rough adjustment) for the even green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Latest: GO Color |
- |
Displays the black offset value (rough adjustment) for the odd green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4625 |
[Black Level Rough Adj. Display] BE: Blue Even signal, BO: Blue Odd signal |
||
001 |
Latest: BE Color |
- |
Displays the black offset value (rough adjustment) for the even blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Latest: BO Color |
- |
Displays the black offset value (rough adjustment) for the odd blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4628 |
[Analog Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Red. |
|||
001 |
Latest: R Color |
- |
[0 to 7 / 0 / 1 digit/step] |
4629 |
[Analog Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Green. |
|||
001 |
Latest: G Color |
- |
[0 to 7 / 0 / 1 digit/step] |
4630 |
[Analog Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Blue. |
|||
001 |
Latest: B Color |
- |
[0 to 7 / 0 / 1 digit/step] |
4631 |
[Digital Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Red. |
|||
001 |
Latest: RE Color |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Latest: RO Color |
- |
4632 |
[Digital Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Green. |
|||
001 |
Latest: GE Color |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Latest: GO Color |
- |
4633 |
[Digital Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Blue. |
|||
001 |
Latest: BE Color |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Latest: BO Color |
- |
4645 |
[Scan Adjust Error] |
||
001 |
White level |
- |
[0 to 65535 / 0 / 1 digit/step] |
002 |
Black level |
- |
4647 |
[Read Hard Error] |
||
Displays the result of the SBU connection check. |
|||
001 |
Power-ON |
- |
[0 to 35535 / 0 / 1digit /step] 0: OK, Other: SBU connection check failure If the SBU connection check fails, SC144 occurs. |
4654 |
[Black Level Adj. Display] RE: Red Even signal, RO: Red Odd signal |
||
001 |
Last Correct Value: RE Color |
*ENG |
Displays the black offset value for the even red signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Last Correct Value: RO Color |
*ENG |
Displays the black offset value for the odd red signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4655 |
[Black Level Adj. Display] GE: Green Even signal, GO: Green Odd signal |
||
001 |
Last Correct Value: GE Color |
*ENG |
Displays the black offset value for the even green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Last Correct Value: GO Color |
*ENG |
Displays the black offset value for the odd green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4656 |
[Black Level Adj. Display] BE: Blue Even signal, BO: Blue Odd signal |
||
001 |
Last Correct Value: BE Color |
*ENG |
Displays the black offset value for the even blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Last Correct Value: BO Color |
*ENG |
Displays the black offset value for the odd blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4658 |
[Analog Gain Adjustment] |
||
Displays the previous gain value of the amplifiers on the controller for Red. |
|||
001 |
Last Correct Value: RE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4659 |
[Analog Gain Adjustment] |
||
Displays the previous gain value of the amplifiers on the controller for Green. |
|||
001 |
Last Correct Value: GE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4660 |
[Analog Gain Adjustment] |
||
Displays the previous gain value of the amplifiers on the controller for Blue. |
|||
001 |
Last Correct Value: BE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4661 |
[Digital Gain Adjustment] RE: Red Even signal, RO: Red Odd signal |
||
001 |
Last Correct Value: RE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Last Correct Value: RO Color |
*ENG |
4662 |
[Digital Gain Adjustment] GE: Green Even signal, GO: Green Odd signal |
||
001 |
Last Correct Value: GE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Last Correct Value: GO Color |
*ENG |
4663 |
[Digital Gain Adjustment] BE: Blue Even signal, BO: Blue Odd signal |
||
001 |
Last Correct Value: BE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Last Correct Value: BO Color |
*ENG |
4673 |
[Black Level Adj. Display] RE: Red Even signal, RO: Red Odd signal |
||
001 |
Factory Setting: RE Color |
*ENG |
Displays the factory setting values of the black level adjustment for the even red signal in the CCD circuit board (color printing speed).. [0 to 16383 / 0 / 1 digit/step] |
002 |
Factory Setting: RO Color |
*ENG |
Displays the factory setting values of the black level adjustment for the odd red signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4674 |
[Black Level Adj. Display] GE: Green Even signal, GO: Green Odd signal |
||
001 |
Factory Setting: GE Color |
*ENG |
Displays the factory setting values of the black level adjustment for the even green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Factory Setting: GO Color |
*ENG |
Displays the factory setting values of the black level adjustment for the odd green signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4675 |
[Black Level Adj. Display] BE: Blue Even signal, BO: Blue Odd signal |
||
001 |
Factory Setting: BE Color |
*ENG |
Displays the factory setting values of the black level adjustment for the even blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
002 |
Factory Setting: BO Color |
*ENG |
Displays the factory setting values of the black level adjustment for the odd blue signal in the CCD circuit board (color printing speed). [0 to 16383 / 0 / 1 digit/step] |
4677 |
[Analog Gain Adjustment] |
||
Displays the factory setting values of the gain adjustment for Red. |
|||
001 |
Factory Setting: RE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4678 |
[Analog Gain Adjustment] |
||
Displays the factory setting values of the gain adjustment for Green. |
|||
001 |
Factory Setting: GE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4679 |
[Analog Gain Adjustment] |
||
Displays the factory setting values of the gain adjustment for Blue. |
|||
001 |
Factory Setting: BE Color |
*ENG |
[0 to 7 / 0 / 1 digit/step] |
4680 |
[Digital Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Red. |
|||
001 |
Factory Setting: RE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Factory Setting: RO Color |
*ENG |
4681 |
[Digital Gain Adjustment ] |
||
Displays the gain value of the amplifiers on the controller for Green. |
|||
001 |
Factory Setting: GE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Factory Setting: GO Color |
*ENG |
4682 |
[Digital Gain Adjustment] |
||
Displays the gain value of the amplifiers on the controller for Blue. |
|||
001 |
Factory Setting: BE Color |
*ENG |
[0 to 1023 / 0 / 1 digit/step] |
002 |
Factory Setting: BO Color |
*ENG |
4688 |
[Scan Image Density Adjustment] |
||
Adjusts the white shading parameter when scanning an image with the ARDF or 1-pass DF. Adjusts the density level if the ID of outputs made in the DF and Platen mode is different. |
|||
001 |
ARDF |
*ENG |
[50 to 150 / 98 / 1%/ step ] |
002 |
1-pass DF |
*ENG |
[50 to 150 / 98 / 1%/ step ] |
4690 |
[White Level Peak Read] |
||
Displays the peak level of the white level scanning. |
|||
001 |
RE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
RO |
- |
4691 |
[White Level Peak Read] |
||
Displays the peak level of the white level scanning. |
|||
001 |
GE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
GO |
- |
4692 |
[White Level Peak Read] |
||
Displays the peak level of the white level scanning. |
|||
001 |
BE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
BO |
- |
4693 |
[Black Level Peak Read] |
||
Displays the peak level of the black level scanning. |
|||
001 |
RE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
RO |
- |
4694 |
[Black Level Peak Read] |
||
Displays the peak level of the black level scanning. |
|||
001 |
GE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
GO |
- |
4695 |
[Black Level Peak Read] |
||
Displays the peak level of the black level scanning. |
|||
001 |
BE |
- |
[0 to 1023 / 0 / 1 digit/step] |
002 |
BO |
- |
4802 |
[DF Shading FreeRun] |
||
001 |
Lamp OFF |
- |
Executes the scanner free run of shading movement with exposure lamp on or off. Press "OFF" to stop this free run. Otherwise, the free run lasts. |
002 |
Lamp ON |
4804 |
[Home Position] |
||
001 |
- |
- |
Executes the scanner HP detection. |
4806 |
[Carriage Save] |
||
001 |
- |
- |
Moves the carriage from the scanner home position. Dust may fall through the DF exposure glass. Therefore, do this SP when you transport the machine a long distance. |
4807 |
[SBU Test Pattern Change] |
||
001 |
- |
- |
[0 to 250 / 0 / 1 /step] 1: Grid pattern 2: Gradation main scan 3: Gradation sub scan 4 to 250: Default (Scanning Image) |
4808 |
[Factory Setting Input] |
||
002 |
Execution Flag |
- |
[0 or 1 / 0 / 1 /step] |
4902 |
[ACC Data Display] |
||
This SP outputs the final data read at the end of ACC execution. A zero is returned if there was an error reading the data. [0 to 255 / 0 / 1 /step] |
|||
001 |
R DATA1 |
*ENG |
Photo C Patch Level 1 (8-bit) |
002 |
G DATA1 |
*ENG |
Photo M Patch Level 1 (8-bit) |
003 |
B DATA1 |
*ENG |
Photo Y Patch Level 1 (8-bit) |
004 |
R DATA2 |
*ENG |
Photo C Patch Level 17 (8-bit) |
005 |
G DATA2 |
*ENG |
Photo M Patch Level 17(8-bit) |
006 |
B DATA2 |
*ENG |
Photo Y Patch Level 17 (8-bit) |
4918 |
[Manual Gamma Adj] |
||
Adjusts the offset data of the printer gamma for yellow in Photo mode. See “Printer Gamma Correction" in the Replacement and Adjustment for how to use. |
|||
009 |
- |
- |
Enter the manual gamma adjustment screen (-001 to 008). For details, see the "Printer Gamma Correction" in the section "Replace and Adjustment". |
4954 |
[Read/Restore Std] |
||
001 |
Read New Chart |
- |
Execute the scanning of the A4 chart. |
002 |
Recall Prev Chart |
- |
Clear the data of the scanned A4 chart. |
003 |
Read Std Chart |
- |
Execute the scanning of the A4 standard chart. |
004 |
Set Std Chart |
- |
Overwrite the standard data. |
4991 |
[IPU Image Path Selection ] |
||
Selects the image path. Enter the number to be selected using the 10-key pad. |
|||
001 |
RGB Frame Memory |
*ENG |
[0 to 11 / 2 / 1 /step ] |
0: Scanner input RGB images 1: Scanner I/F RGB images 2: RGB images done by Shading correction (Shading ON, Black offset ON) 3: Shading data 4 to 11: Not used |
4993 |
[High Light Correction] |
||
001 |
Sensitivity Selection |
*ENG |
Selects the Highlight correction level. [0 to 9 / 4 / 1 /step] 0: weakest sensitivity 9: strongest sensitivity |
002 |
Range Selection |
*ENG |
Selects the range level of Highlight correction. [0 to 9 / 4 / 1 /step] 0: weakest skew correction, 9: strongest skew correction |
4994 |
[Text/Photo Detection Level Adj.] |
||
Selects the definition level between Text and Photo for high compression PDF. |
|||
001 |
PDF Sensitivity Level text/photo |
*ENG |
[0 to 2 / 1 / 1 /step] 0: Text priority 1: Normal 2: Photo priority |