Top Page > Main Chapters > System Maintenance > Main SP Tables-6 > SP6-XXX (Peripherals)

SP6-XXX (Peripherals)

6006	[ADF Adj.] ADF Adjustment
	Adjusts the side-to-side and leading registration of originals with the ARDF.
001	Side-to-Side Registration	*ENG	[-3.0 to 3.0 / 0 / 0.1 mm/step ]
002	Side-to-Side Registration	*ENG	[-3.0 to 3.0 / 0 / 0.1 mm/step ]
003	Leading Edge Registration	*ENG	[-5.0 to 5.0 / 0 / 0.1 mm/step ]
	Adjusts the amount of paper buckle to correct original skew for the front and rear sides.
005	Buckle: Duplex Front	*ENG	[-3.0 to 3.0 / 0 / 0.1 mm/step ]
006	Buckle: Duplex Rear	*ENG	[-2.5 to 2.5 / 0 / 0.1 mm/step ]
	Adjusts the erase margin at the original trailing edge.
007	Rear Edge Erase	*ENG	[-10 to 10 / 0 / 0.1 mm/step ]

6007	[ADF INPUT Check]
	Displays the signals received from the sensors and switches of the ARDF. Only Bit 0 is used for ADF input check ( Main SP Tables-9 in this section).

6008

[ADF OUTPUT Check]

Activates the electrical components for functional check.

It is not possible to activate more than one component at the same time (Main SP Tables-9 in this section).

6009	[ADF Free Run]
	Performs a DF free run in simplex, duplex mode or stamp mode.
001	Free Run Simplex Motion	-	-
002	Free Run Duplex Motion	-
003	Free Run Stamp Motion	-

6010	[Stamp Position Adj.] Fax Stamp Position Adjustment
	Adjusts the horizontal position of the stamp on the scanned originals.
6010 1	Stamp Position Adj.	*ENG	[-5.0 to 5.0 / 0 / 1 mm/step]

6016	[Original Size Detection Priority] Original Size Detection Priority
	Specifies the original size for a size detected by the original sensor, since original sensors cannot recognize all sizes.
001	Original Size Detection Priority	*ENG	[0 or 1 / 0 / - ] 0: Setting 1, 1: Setting 2
		NA	Setting 1	Setting 2
			DLT SEF	Folio SEF 11" x 15"
			LG SEF	Foolscap SEF
			LT SEF	US EXE 8" x 10"
			LT LEF	US EXE LEF
		EU/ ASIA	DLT SEF	8K 267 x 390 mm
			LT SEF	16K 195 x 267 mm
			LT LEF	16K 267 x 195 mm

6017	[DF Magnification Adj.] DF Magnification Adjustment
	Adjusts the magnification in the sub-scan direction for the ARDF.
001	DF Magnification Adj.	*CTL	[-5.0 to 5.0 / 0 / 0.1 %/step]

6020

[Skew Correction Moving Setting]

Turns the original skew correction in the ARDF for all original sizes on or off.

001

*ENG

[0 or 1 / 0 / - ]

0: Off (only for small original sizes)

1: On (for all original sizes)

6128	[Punch Position: Sub Scan]
6128	Adjusts the punching position in the sub scan direction.
001	1.Domestic 2Hole (Europe 2Hole)	*ENG	[-7.5 to 7.5 / 0 / 0.5 mm/step]
002	2.North America 3Hole	*ENG
003	3.Europe 4Hole	*ENG
004	4.North Europe 4Hole	*ENG
005	5.North Europe 2Hole	*ENG

6129	[Punch Position: Main Scan]
6129	Adjusts the punching position in the main scan direction.
001	1.Domestic 2Hole (Europe 2Hole)	*ENG	[-2.0 to 2.0 / 0 / 0.4 mm/step]
002	2.North America 3Hole	*ENG
003	3.Europe 4Hole	*ENG
004	4.North Europe 4Hole	*ENG
005	5.North Europe 2Hole	*ENG

6130	[Skew Correction: Buckle Adj.]
6130	Adjusts the paper buckle for each paper size.
001	A3T	*ENG	[-5.0 to 5.0 / 0 / 0.25 mm/step]
002	B4T	*ENG
003	A4T	*ENG
004	A4Y	*ENG
005	B5T	*ENG
006	B5Y	*ENG
007	DLT-T	*ENG
008	LG-T	*ENG
009	LT-T	*ENG
010	LT-Y	*ENG
011	12" x 18"	*ENG
012	Other	*ENG

6131	[Skew Correction Control]
6131	Selects the skew correction control for each paper size. These are only activated for B804/B805.
001	A3T	*ENG	[0 or 1 / 1 / 1/step] 0: No (No skew correction) 1: Roller Stop Skew Correction
002	B4T	*ENG
003	A4T	*ENG
004	A4Y	*ENG
005	B5T	*ENG
006	B5Y	*ENG
007	DLT-T	*ENG
008	LG-T	*ENG
009	LT-T	*ENG
010	LT-Y	*ENG
011	12" x 18"	*ENG
012	Other	*ENG

6132	[Jogger Fence Fine Adj]
6132	This SP adjusts the distance between the jogger fences and the sides of the stack on the finisher stapling tray in the (Booklet) Finisher B804/B805. The adjustment is done perpendicular to the direction of paper feed.
001	A3T	*ENG	[-1.5 to 1.5 / 0 / 0.5 mm/step] + Value: Increases distance between jogger fences and the sides of the stack. - Value: Decreases the distance between the jogger fences and the sides of the stack.
002	B4T	*ENG
003	A4T	*ENG
004	A4Y	*ENG
005	B5T	*ENG
006	B5Y	*ENG
007	DLT-T	*ENG
008	LG-T	*ENG
009	LT-T	*ENG
010	LT-Y	*ENG
011	12" x 18"	*ENG
012	Other	*ENG

6133

[Staple Position Adjustment]

Adjusts the staple position for each finisher (B408/B804/B805).

+ Value: Moves the staple position to the rear side.

- Value: Moves the staple position to the front side.

001

Finisher (B408/B804/B805)

*ENG

[-3.5 to 3.5 / 0 / 1/step]

6134	[Saddle Stitch Position Adjustment]
	Use this SP to adjust the stapling position of the booklet stapler when paper is stapled and folded in the Booklet Finisher B804.
001	A3T	[-3.0 to 3.0 / 0 / 0.2 mm/step] + Value: Shifts staple position toward the crease. - Value: Shifts staple position away from the crease.
002	B4T
003	A4T
004	B5T
005	DLT-T
006	LG-T
007	LT-T
008	12" x 18"
009	Other

6135	[Folder Position Adj.]
	This SP corrects the folding position when paper is stapled and folded in the Booklet Finisher B804.
001	A3T	[-3.0 to 3.0 / 0 / 0.2 mm/step] + Value: Shifts staple position toward the crease. - Value: Shifts staple position away from the crease.
002	B4T
003	A4T
004	B5T
005	DLT-T
006	LG-T
007	LT-T
008	12" x 18"
009	Other

6136	[Folding Number]
	Sets the number of times that folding is done in the Booklet Finisher B804.
001	-	[2 to 30 / 2 / 1 time/step]

6138	[FIN (TIG) INPUT Check] Finisher (B793) Input Check
	Displays the signals received from sensors and switches of the booklet finisher. (Main SP Tables-9 in this section)

6139	[FIN (KIN) INPUT Check] Finisher (B408) Input Check
	Displays the signals received from sensors and switches of the booklet finisher. (Main SP Tables-9 in this section)

6143	[FIN (TIG) OUPUT Check] Finisher (B793) Output Check
	Displays the signals received from sensors and switches of the booklet finisher. (Main SP Tables-9 in this section)

6144	[FIN (KIN) OUPUT Check] Finisher (B408) Output Check
	Displays the signals received from sensors and switches of the booklet finisher. (Main SP Tables-9 in this section)

6145	[FIN (ELB) INPUT Check] Finisher (D372) Input Check
	Displays the signals received from sensors and switches of the 500-sheet finisher. (Main SP Tables-9 in this section)

6146	[FIN (ELB) OUPUT Check] Finisher (D372) Output Check
	Displays the signals received from sensors and switches of the 500-sheet finisher. (Main SP Tables-9 in this section)

6149

[Max. Pre-Stack Sheet]

*ENG

Number of Pre-Stack Sheets

This SP sets the number of sheets sent to the pre-stack tray.

Note:

You may need to adjust this setting or switch it off when feeding thick or slick paper.

001

[0 to 3 / 3 / 1 sheet/step]

6150	[INPUT Check]
	Displays the signals received from sensors and switches of the bridge unit (D386)/ side tray (D542) (Main SP Tables-9 in this section).

6151	[OUTPUT Check]
	Displays the signals received from sensors and switches of the bridge unit (D386)/ side tray (D542) (Main SP Tables-9 in this section).

6152	[INPUT Check]
	Displays the signals received from sensors and switches of the shift tray (D388) (Main SP Tables-9 in this section).

6153	[OUTPUT Check]
	Displays the signals received from sensors and switches of the shift tray (D388) (Main SP Tables-9 in this section).

6154	[INPUT Check]
	Displays the signals received from sensors and switches of the 1 bin tray (D536) (Main SP Tables-9 in this section).

6155	[OUTPUT Check]
6155	Displays the signals received from sensors and switches of the 1 bin tray (D536) (Main SP Tables-9 in this section)
001	1 bin: Junction Solenoid

6160	[INPUT Check]
	Displays the signals received from sensors and switches of the two-tray paper feed unit (D537), LCT 2000 (D538) and LCT 1200 (D539) (Main SP Tables-9 in this section)

6161	[OUTPUT Check]
	Displays the signals received from sensors and switches of the two-tray paper feed unit (D537), LCT 2000 (D538) and LCT 1200 (D539) (Main SP Tables-9 in this section)